Rapid Consolidation of TiN-Cr_2N-(Ti,Cr)N Nanoparticles Using Pulsed Current Activated Sintering and the Mechanical Properties of Sintered Product
スポンサーリンク
概要
- 論文の詳細を見る
- 2012-08-01
著者
-
Kim Wonbaek
Division Of Minerals & Materials Processing Korea Institute Of Geoscience & Mineral Resource
-
Shon In-jin
Div. Of Advanced Materials Engineering The Res. Center Of Advanced Materials Dev. Chonbuk National U
-
Du Song-lee
Division Of Advanced Materials Engineering The Research Center Of Advanced Materials Development Cho
-
Suh Chang-yul
Mineral Resource Research Division Korea Insititute Of Geoscience And Mineral Resources
-
Kim Wonbaek
Mineral Resource Research Division Korea Insititute Of Geoscience And Mineral Resources
-
Shon In-jin
Division Of Advanced Materials Engineering And The Research Center Of Advanced Materials Development
-
Lim Jae-won
Mineral Resources Res. Div. Korea Inst. Of Geoscience And Mineral Resources
-
Lim Jae-won
Minerals And Materials Processing Division Korea Institute Of Geoscience Mining And Materials Resources
-
ROH Ki-Min
Minerals and Materials Processing Division, Korea Institute of Geoscience, Mining and Materials Resources
-
Roh Ki-min
Minerals And Materials Processing Division Korea Institute Of Geoscience Mining And Materials Resources
-
Du Song-lee
Division Of Advanced Materials Engineering Research Center Of Advanced Materials Development Chonbuk National University
関連論文
- Recovery of Platinum and Palladium from the Spent Petroleum Catalysts by Substrate Dissolution in Sulfuric Acid
- Synthesis of TiN Nanoparticles by Explosion of Ti Wire in Nitrogen Gas
- Ti-Cr Nanoparticles Prepared by Electrical Wire Explosion
- Effect of Sputtering Power on the Nucleation and Growth of Cu Films Deposited by Magnetron Sputtering
- Effect of Ar/Ar-H_2 Plasma Arc Melting on Cu Purification
- Characteristics of Printed Thin Films Using Indium Tin Oxide (ITO) Ink
- Influence of Substrate Bias Voltage on the Impurity Concentrations in Hf Films Deposited by Ion Beam Deposition Method
- Agglomeration of Copper Thin Film in Cu/Ta/Si Structure
- Influence of Substrate Bias Voltage on the Properties of Cu Thin Films by Sputter Type Ion Beam Deposition
- Improvement of Ta Barrier Film Properties in Cu Interconnection by Using a Non-mass Separated Ion Beam Deposition Method
- Nanosize Particles of ZrVFe Alloy by Pulsed Laser Ablation in Ethanol
- Electrical Wire Explosion of Cr-Coated Ti Wire in N_2 Gas
- Rapid Consolidation of Nanostructured TiCu Compound by High Frequency Induction Heating and Its Mechanical Properties
- Preparation of Titanium-Chromium Nitride by Gas Nitriding of the Explosion Products of Cr-Coated Ti Wire
- Microstructure of Ti-Cr Nanoparticles Prepared by Electrical Wire Explosion
- Adsorption of Cd(II) on Waste Calcite Produced by the Carbonation of Flue Gas Desulfurization (FGD) Gypsum
- Enhanced Cd(II) Uptake by the Bassanite Phase Contained in Waste Calcite Produced via the Carbonation of Flue Gas Desulfurization (FGD) Gypsum
- Mechanical Synthesis and Rapid Consolidation of Nanocrystalline TiAl-Al_2O_3 Composites by High Frequency Induction Heated Sintering
- Rapid Synthesis and Consolidation of Nanostructured Mg_2SiO_4-MgAl_2O_4 Composites
- Rapid Consolidation of TiN-CrN-(Ti,Cr)N Nanoparticles Using Pulsed Current Activated Sintering and the Mechanical Properties of Sintered Product
- Pulsed Current Activated Synthesis and Consolidation of Nanostructured MgTiO Compound
- Preparation of Ultra-High Purity Cylindrical Mo Ingot by Electron Beam Drip Melting
- Properties and Rapid Consolidation of Nanocrystalline TiCo Compounds by High-Frequency Induction Heated Sintering
- Simultaneous Synthesis and Densification of a Nanocrystalline (W,Ti)Si_2-SiC Composite from Mechanically Activated Powders by High Frequency Induction Heating
- The Effect of Phases in Nanoparticles Produced by Electrical Wire Explosion on Arsenic(III) Removal
- Pulsed Current Activated Synthesis and Consolidation of Nanostuctured MgTiO_3 Compound
- Rapid Consolidation of TiN-Cr_2N-(Ti,Cr)N Nanoparticles Using Pulsed Current Activated Sintering and the Mechanical Properties of Sintered Product