Effects of Macro- and Micro-Porosity on Mechanical Properties of a Porous Ti-6Al-4V Alloy Fabricated Using Solid-State Space-Holder Method
スポンサーリンク
概要
- 論文の詳細を見る
The effect of macro and micro porosity on properties of porous Ti-6Al-4V samples fabricated using a solid state space holder method is investigated. Sintering with mixing condition, with and without process control agents (PCA), and sintering conditions, pressure and temperature range of 30–60 MPa and 700–725°C were performed in order to get different macro pore morphology and micro pore quantity. It is found that macro-pore plays significant role to determine the properties of porous Ti-6Al-4V. Open porosity, Young's modulus and strength are affected by the distribution of the pores. Randomly distributed pores will results in high value of open porosity yet higher Young's modulus. Micro porosity only less affects on the mechanical properties of the porous product.
著者
-
Tezuka Hiroyasu
Department Of Metallurgical Engineering Tokyo Institute Of Technology
-
Kobayashi Equo
Department Of Metallurgy And Ceramics Science Graduate School Of Engineering Tokyo Institute Of Tech
-
Kobayashi Equo
Department of Metallurgy and Ceramics Science, Tokyo Institute of Technology
-
Sato Tatsuo
Precision and Intelligence Laboratory, Tokyo Institute of Technology
-
Lantang Yorina
Department of Metallurgy and Ceramics Science, Tokyo Institute of Technology
関連論文
- Growth of Primary a Phase in the Semi-Solid State Mg-Zn-Ca-Zr Alloy
- Tensile Behavior of Mg-Zn-Ca-Zr Alloy forged in Semi-Solid State
- Bending Property of Super-Elastic Ti-Ni Alloy Dental Castings with Different Heat Treatments
- Determination of the Immobilization Manner of Amine-Terminated Poly(Ethylene Glycol) Electrodeposited on a Titanium Surface with XPS and GD-OES
- Fabrication and Mechanical Properties of Porous Ti/HA Composites for Bone Fixation Devices
- Mechanical Properties and Structure of Ignition-Proof Mg-Ca-Zr Alloys Produced by Squeeze Casting
- Mechanical Properties and Fracture Process of SiC_w/Mg Composites Produced by Squeeze Casting and Extrusion
- Castability of Ti-6Al-7Nb alloy for dental casting
- Inhibition Effect of Zirconium Coating on Calcium Phosphate Precipitation of Titanium to Avoid Assimilation with Bone
- Fatigue Property of Ti-5Al-13Ta Alloy Dental Castings in 0.9% NaCl Solution
- Fatigue Life Prediction of Biomedical Titanium Alloys under Tensile/Torsional Stress
- Mechanical Strength and Microstructure of Laser-welded Ti-6Al-7Nb Alloy Castings
- Improved Biocompatibility of Titanium-Zirconium (Ti-Zr) Alloy : Tissue Reaction and Sensitization to Ti-Zr Alloy Compared with Pure Ti and Zr in Rat Implantation Study
- Fatigue Property of Super-Elastic Ti-Ni Alloy Dental Castings
- Bending Properties of Co-Ni-Cr-Mo Alloy Wire for Orthodontic Application
- Deformation Properties of Ti-6Al-7Nb Alloy Castings for Removable Partial Denture Frameworks
- Tissue Reactions and Sensitivity to Iron-Chromium Alloys
- A Method to Monitor Corrosion of Chromium-iron Alloys by Monitoring the Chromium Ion Concentration in Urine
- Mechanical and Fatigue Properties of Biomedical Titanium Alloys under Combined (Tensile/Torsional)Stress
- Effects of Thermal Residual Stress on Mechanical Properties of SiC Whisker Reinforced Al-Mg and Al-Li Alloys Composites
- Analysis of Thermal Residual Stresses in Unidirectionally Aligned SiCw/Al-Alloy Matrix Composites by X-ray Diffraction
- SEM Observation on the Surface of Titanium Miniplates Retrieved from Patients after Maxillofacial Surgical Treatment
- Deformation Property of Titanium and Dental Alloys in an Indentation Test
- Microstructures and Mechanical Properties of Al_3Fe Reinforced Aluminum Matrix Composites Fabricated by a Plasma Synthesis Method
- Dry Sliding Wear Behavior of A2218/Al_3Fe Composites Fabricated by Plasma Synthesis Method
- Microstructural Changes in Al-Cu-Mn Alloy Reinforced with SiC Particles on Holding at high Temperatures
- Precipitation Behavior of P/M Hypereutectic Al-Si-Cu-Mg Alloys Containing Fe and Ni
- Semi-Solid Microstructure Control of Wrought Al-Mg-Si Based Alloys with Fe and Mn Additions in Deformation-Semi-Solid-Forming Process
- Effects of Cu Addition on Behavior of Nanoclusters during Multi-Step Aging in Al-Mg-Si Alloys
- Influence of Sr and Mn Additions on Intermetallic Compound Morphologies in Al-Si-Cu-Fe Cast Alloys
- Fabrication and Mechanical Properties of Al-Based In Situ Nano-Composites Reinforced by Al_2O_3 and Intermetallic Compounds
- Caliber Rolling Process and Mechanical Properties of High Fe-Containing Al-Mg-Si Alloys
- Effects of Sintering Conditions on Mechanical Properties of Biomedical Porous Ti Produced by Spark Plasma Sintering
- Effect of Ca Addition on Precipitation Behavior of Mg-6.0 mass %Zn-3.0 mass% Al Alloy
- Accelerated Calcium Phosphate Formation on Titanium Utilizing Galvanic Current between Titanium and Gold in Hanks' Solution
- Formation Behavior of Nanoclusters in Al-Mg-Si Alloys with Different Mg and Si Concentration
- Effects of Macro- and Micro-Porosity on Mechanical Properties of a Porous Ti-6Al-4V Alloy Fabricated Using Solid-State Space-Holder Method