Mechanical Properties and Fracture Process of SiC_w/Mg Composites Produced by Squeeze Casting and Extrusion

スポンサーリンク

概要

• 論文の詳細を見る
• Japan Institute of Metalsの論文

著者

• Chang S‐y

  Hankuk Aviation Univ. Kyunggi‐do Kor

• CHANG Si-young

  Department of Metallurgy and Materials Science, Hanyang University

• TEZUKA Hiroyasu

  Department of Metallurgical Engineering, Tokyo Institute of Technology

• KAMIO Akihiko

  Department of Metallurgical Engineering, Tokyo Institute of Technology

• Kamio A

  Tokyo Inst. Technol. Tokyo Jpn

• Kamio Akihiko

  Department Of Metallurgical Engineering Faculty Of Engineering Tokyo Institute Of Technology

• Chang Si-young

  Department Of Metallurgy And Materials Science Hanyang University

• Chang Si-young

  Department Of Materials Engineering Hankuk Aviation University

• Tezuka H

  Tokyo Inst. Technol. Tokyo Jpn

• Tezuka Hiroyasu

  Department Of Metallurgical Engineering Tokyo Institute Of Technology

関連論文

• Growth of Primary a Phase in the Semi-Solid State Mg-Zn-Ca-Zr Alloy
• Tensile Behavior of Mg-Zn-Ca-Zr Alloy forged in Semi-Solid State
• Effect of Equal Channel Angular Pressing on the Distribution of Reinforcements in the Discontinuous Metal Matrix Composites
• Microstructures and Mechanical Properties of Equal Channel Angular Pressed 5083 Al Alloy
• Mechanical Properties and Structure of Ignition-Proof Mg-Ca-Zr Alloys Produced by Squeeze Casting
• Mechanical Properties and Fracture Process of SiC_w/Mg Composites Produced by Squeeze Casting and Extrusion
• Effect of Yttrium on High Temperature Strength of Magnesium
• Effect of Heat Treatment on Tensile Properties of Component with Macro-Interface between Unreinforced Magnesium and Composite
• Effects of Thermal Residual Stress on Mechanical Properties of SiC Whisker Reinforced Al-Mg and Al-Li Alloys Composites
• Analysis of Thermal Residual Stresses in Unidirectionally Aligned SiCw/Al-Alloy Matrix Composites by X-ray Diffraction
• Field-Emission Activation on Boron-Doped Chemical-Vapor-Deposited Polycrystalline Diamond Films
• Improvement of Mechanical Characteristics in Severely Plastic deformed Mg Alloys
• Microstructures and Mechanical Properties of Al_3Fe Reinforced Aluminum Matrix Composites Fabricated by a Plasma Synthesis Method
• Dry Sliding Wear Behavior of A2218/Al_3Fe Composites Fabricated by Plasma Synthesis Method
• Microstructural Changes in Al-Cu-Mn Alloy Reinforced with SiC Particles on Holding at high Temperatures
• Precipitation Behavior of P/M Hypereutectic Al-Si-Cu-Mg Alloys Containing Fe and Ni
• Microstructures and coarsening behavior of silicon particles in P/M Al-Si-Cu-Mg alloys containing Fe and Ni
• Effects of Defects and Fe Intermetallic Compounds on Fatigue Properties of Al-Si-Cu-Mg Alloy Castings
• Model for the Calculation of Precipitation and Recrystallization Behavior during the Annealing Process in Copper Alloys
• Semi-Solid Microstructure Control of Wrought Al-Mg-Si Based Alloys with Fe and Mn Additions in Deformation-Semi-Solid-Forming Process
• Influence of Sr and Mn Additions on Intermetallic Compound Morphologies in Al-Si-Cu-Fe Cast Alloys
• Fabrication and Mechanical Properties of Al-Based In Situ Nano-Composites Reinforced by Al_2O_3 and Intermetallic Compounds
• Caliber Rolling Process and Mechanical Properties of High Fe-Containing Al-Mg-Si Alloys
• Effects of Sintering Conditions on Mechanical Properties of Biomedical Porous Ti Produced by Spark Plasma Sintering
• Effect of Ca Addition on Precipitation Behavior of Mg-6.0 mass %Zn-3.0 mass% Al Alloy
• Formation Behavior of Nanoclusters in Al-Mg-Si Alloys with Different Mg and Si Concentration
• Effects of Macro- and Micro-Porosity on Mechanical Properties of a Porous Ti-6Al-4V Alloy Fabricated Using Solid-State Space-Holder Method

もっと見る 閉じる

スポンサーリンク