Effects of Thermal Residual Stress on Mechanical Properties of SiC Whisker Reinforced Al-Mg and Al-Li Alloys Composites

スポンサーリンク

概要

• 論文の詳細を見る

著者

• Hong S‐k

  Chonnam National Univ. Kwangju Kor

• TEZUKA Hiroyasu

  Department of Metallurgical Engineering, Tokyo Institute of Technology

• KAMIO Akihiko

  Department of Metallurgical Engineering, Tokyo Institute of Technology

• Kamio A

  Tokyo Inst. Technol. Tokyo Jpn

• Kamio Akihiko

  Department Of Metallurgical Engineering Faculty Of Engineering Tokyo Institute Of Technology

• Tezuka H

  Tokyo Inst. Technol. Tokyo Jpn

• Tezuka Hiroyasu

  Department Of Metallurgical Engineering Tokyo Institute Of Technology

• Hong Sung-kil

  Department Of Metallurgical Engineering Chonnam National University

関連論文

• Growth of Primary a Phase in the Semi-Solid State Mg-Zn-Ca-Zr Alloy
• Tensile Behavior of Mg-Zn-Ca-Zr Alloy forged in Semi-Solid State
• Mechanical Properties and Structure of Ignition-Proof Mg-Ca-Zr Alloys Produced by Squeeze Casting
• Mechanical Properties and Fracture Process of SiC_w/Mg Composites Produced by Squeeze Casting and Extrusion
• Effect of Yttrium on High Temperature Strength of Magnesium
• Effect of Heat Treatment on Tensile Properties of Component with Macro-Interface between Unreinforced Magnesium and Composite
• Effects of Thermal Residual Stress on Mechanical Properties of SiC Whisker Reinforced Al-Mg and Al-Li Alloys Composites
• Analysis of Thermal Residual Stresses in Unidirectionally Aligned SiCw/Al-Alloy Matrix Composites by X-ray Diffraction
• Microstructures and Mechanical Properties of Al_3Fe Reinforced Aluminum Matrix Composites Fabricated by a Plasma Synthesis Method
• Dry Sliding Wear Behavior of A2218/Al_3Fe Composites Fabricated by Plasma Synthesis Method
• Microstructural Changes in Al-Cu-Mn Alloy Reinforced with SiC Particles on Holding at high Temperatures
• Precipitation Behavior of P/M Hypereutectic Al-Si-Cu-Mg Alloys Containing Fe and Ni
• Microstructures and coarsening behavior of silicon particles in P/M Al-Si-Cu-Mg alloys containing Fe and Ni
• Effects of Defects and Fe Intermetallic Compounds on Fatigue Properties of Al-Si-Cu-Mg Alloy Castings
• Model for the Calculation of Precipitation and Recrystallization Behavior during the Annealing Process in Copper Alloys
• Semi-Solid Microstructure Control of Wrought Al-Mg-Si Based Alloys with Fe and Mn Additions in Deformation-Semi-Solid-Forming Process
• Influence of Sr and Mn Additions on Intermetallic Compound Morphologies in Al-Si-Cu-Fe Cast Alloys
• Fabrication and Mechanical Properties of Al-Based In Situ Nano-Composites Reinforced by Al_2O_3 and Intermetallic Compounds
• Caliber Rolling Process and Mechanical Properties of High Fe-Containing Al-Mg-Si Alloys
• Effects of Sintering Conditions on Mechanical Properties of Biomedical Porous Ti Produced by Spark Plasma Sintering
• Effect of Ca Addition on Precipitation Behavior of Mg-6.0 mass %Zn-3.0 mass% Al Alloy
• Formation Behavior of Nanoclusters in Al-Mg-Si Alloys with Different Mg and Si Concentration
• Effects of Macro- and Micro-Porosity on Mechanical Properties of a Porous Ti-6Al-4V Alloy Fabricated Using Solid-State Space-Holder Method

もっと見る 閉じる

スポンサーリンク