機械構造用炭素鋼の切りくず形態に及ぼす鉛の影響
スポンサーリンク
概要
- 論文の詳細を見る
The orthogonal cutting test was carried out on two structural steels, namely Fe-0.5%C-0.2%Si-0.8%Mn-0.1%Cr containing 0.16%Pb or non-Pb. The chip formation was transferred from shear type to flow type and the cutting force was reduced by the addition of Pb. The lead observed in the shear zone of the chip exhibited a thin string-like morphology, suggesting the ductile and very deformable characteristic of Pb. Those results indicate the major cause of the flow type chip formation. The shear angle can be maintained in the Pb-added steel because of the deformation concentrated on lead particles at the primary shear zone. In the case of low cutting speed conditions, the effect of Pb on machinability mainly reduces shear force in the primary shear zone. As for the lower friction coefficient between tool and chip, the effect of decreasing the cutting force is small.
著者
関連論文
- 高分子液晶を用いた片側パターン電極による選択的研磨制御 : 第1報, ERスラリーのER効果と研磨特性(機械要素,潤滑,工作,生産管理など)
- 熱間鍛造用非調質鋼の炭窒化物析出と高降伏比化
- 非調質鋼の被削性に及ぼすMnS, Pbの影響
- 耐摩耗工具用超硬合金切削における切削油の効果
- 機械構造用炭素鋼の被削性に及ぼす介在物の影響
- 機械構造用炭素鋼の切りくず形態に及ぼす鉛の影響
- CFRPの研削面の生成機構
- 超砥粒ホイールによるCFRPの乾式研削
- 耐摩耗・耐衝撃工具用超硬合金のSEM内微小切削
- CFRP切削における工具摩耗機構II(機械要素,潤滑,工作,生産管理など)
- 超硬合金の切削に関する研究 : 旋削におけるPCD工具の磨耗機構と切削抵抗
- 低炭素快削鋼の構成刃先の成長に及ぼす介在物形態の効果
- 6061アルミニウム合金基複合材料切削時の工具摩耗機構
- オーステンバ処理球状黒鉛鋳鉄の切削における工具摩耗
- 球状黒鉛鋳鉄の高速切削における工具摩耗
- Ca添加機械構造用鋼の切削における超硬工具摩耗抑制効果(力学特性)
- 超硬工具摩耗に及ぼすCa, Mg添加の影響
- 焼結鍛造材切削における工具摩耗
- GFRPの研削表面に及ぼす砥粒形状の影響
- SCr420の高速旋削時における工具摩耗
- チップブレーカに関する研究-湿式旋削時における広域型チップブレーカの切削性能-
- 振動研削切断
- チップブレーカに関する研究
- 非調質鋼の靭性に及ぼす析出物形態の影響
- Tiを添加した高強度クランク軸用 Pb フリー快削非調質鋼の開発
- 低炭素快削鋼の被削性に及ぼす介在物形態の影響と工具摩耗機構
- 低炭素快削鋼を切削した工具摩耗面と鉄凝着物界面の微視的観察
- Effect of Carbide tool Material on Belag formation of Ca-deoxidized Steels
- Micro Structure of Belag and Oxide Inclusions in Ca-deoxidized Steels