Fabrication and Mechanical Properties of Al_2O_3-SiC/TiC/Ni Functionally Graded Materials by SHS/HIP(Materials, Metallurgy & Weldability)
スポンサーリンク
概要
- 論文の詳細を見る
Dense Functionally Graded Materials (FGMs) in the systems of Al_2O_3/TiC/Ni and Al_2O_3-SiC/TiC/Ni were fabricated by SHS/HIP. Due to the rapid high temperature heating and the use of effective additives, the grain growth could be well controlled. The residual stress produced in the outer Al_2O_3 and Al_2O_3-SiC layers, which was induced by the thermal expansion mismatch between the inner TiC/Ni and the outer ceramic layers, was in the range of -220MPa to -500MPa. Two methods were used to measure the R-curve behavior of FGMs. For the indentation-strength method, the compressive stress of the outer ceramic layers showed steep R-curve behavior. For the single edge notch bend (SENB) method, the toughness of the FGM increased in the compression area and reached its maximum of 33MPam^<1/2> at the interface of the compressive stress and the tensile stress areas. In the tension area the value of toughness decreased.
- 大阪大学の論文
著者
-
Miyamoto Yoshinari
Osaka University
-
LIN Junshan
Post Doctral Research Fellow
-
Jin Z
State Key Laboratory For Mechanical Behavior Of Materials Xi'an Jiaotong University
-
Jin Zhihao
State Key Laboratory For Mechanical Behaviro Of Materials Xi'an Jiaotong University
-
Lin J
Joining & Welding Research Institute Osaka University
-
Lin Junshan
Joining And Welding Research Institute Osaka University
-
LIN Junshan
Osaka University
-
Ren Youping
Joining & Welding Research Institute Osaka University
-
Qiao Guanjun
State Key Laboratory For Mechanical Behaviro Of Materials Xi'an Jiaotong University
-
Miyamoto Y
Osaka Univ. Osaka Jpn
関連論文
- 10-O-05 Defect Modes in 3D Photonic Crystal for Microwave Applications
- 01-O-32 SiC Coating on MWCNTs
- 1C24 砂漠砂の Si_3N_4-Si_2N_2O 化合物への転換
- Conversion of Aluminum Dross to Sialon-Based Ceramics by Combustion Synthesis(Materials, Metallurgy & Weldability)
- Fabrication and Mechanical Properties of Al_2O_3/TiC/Ni Symmetric Functionally Graded Materials Doped with Cu and Cu_2O^+(Materials, Metallurgy & Weldability)
- Combustion synthesis of rod-like AlN nanoparticles
- Freeform Fabrication of Titanium by 3D Micro Welding(Materials, Metallurgy & Weldability)
- 301 Freeform Fabrication of Ti-Ni Alloy by Three Dimensional Micro-Welding
- Control of Microwave Emission from Photonic Crystals by Lattice Modification(Materials, Metallurgy & Weldability, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Synthesis of Si_2N_2O-SiC Composites from Desert Sand(Materials, Metallurgy & Weldability)
- Sintering and Toughening Behavior of Dense SiC-coated Diamond Dispersed WC/Co Composites(Materials, Metallurgy & Weldability)
- Fabrication and Mechanical Properties of Al_2O_3-SiC/TiC/Ni Functionally Graded Materials by SHS/HIP(Materials, Metallurgy & Weldability)
- Fabrication of A12O3/TiC/Ni Functionally Graded Materials by Pulsed-Electric Current Sintering and Their Mechamical Properties (特集 傾斜機能材料)
- Fabrication and Mechanical Behavior of Al_2O_3/TiC/Ni Graded Laminates with Surface Compressive Stresses(Materials, Metallurgy & Weldability)
- Microstructures and Mechanical Properties of TiAl/Ti_2AlC Composites Prepared by Pulsed-Electric Current Sintering
- Fabrication of Dense TiAl/Ti_2AlC Composites by Pulsed-Electric Current Sintering and Their Mechanical Properties(Physics, Processes, Instruments & Measurements)
- Microstructure and Oxidation Resistance of Nanometer Sized SiC Coated Diamond Particles(Materials, Metallurgy & Weldability, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Development of Nanostructured SiC Coating on Advanced Carbon Materials and Their Applications
- Spark Plasma Sintering of Al_2O_3-TiC and AL_2O_3-TiC-Diamond Composites(Materials, Metallurgy & Weldability)