Evaluation of Adhesive Behaviors of Chromium Nitride Coating Films Produced by Arc Ion Plating Method
スポンサーリンク
概要
- 論文の詳細を見る
Scratch tests and pin-on-disk wear tests were performed to clarify the cracking and delaminating behavior of CrN coatings. The CrN films were coated onto an aluminum alloy substrate, JIS A2024, by an arc ion plating method. Eight types of single-layered coating and multilayered coatings were prepared by changing the bias voltage during the deposition. L_<CI> and L_<CII> values were not improved by increasing the number of layers. The critical loads of the single-layered coatings decreased with increasing the bias voltage. It appears that, for the multilayered coatings, the combination of bias voltages influenced the critical loads. The critical loads strongly depended on dynamic hardness and Young's modulus. In particular, the critical loads of the multilayered coatings were influenced by the properties of the intermediate and bottom layers as well as the surface roughness, hardness and Young's modulus of the top layer. The large film delamination for single-layered coatings deposited using a high bias voltage occurred during pin-on-disk wear tests even though the critical loads of the single-layered coatings were higher than those of the multilayered coatings. If the brittle top layer could be broken and delaminated by the sliding contact, the ductile bottom layer coated under a bias voltage of 0 V could endure the complete delamination of film.
- 2006-01-15
著者
-
KIM Yun
Department of wind engineering, Hyundai Institute of Construction Technology
-
Kimura Kazushi
Department Of Anatomy And Neurobiology Kyoto University Graduate School Of Medicine.
-
Kimura Kazushi
Department Of Mechanical Engineering The University Of Tokushima
-
Kim Yun
Department Of Mechanical And Materials Engineering Korea Maritime University
-
Kim Yun
Department Of Chemistry Korea Advanced Institute Of Science & Technology
-
Murakami Ri-ichi
Department Of Mechanical Engineering Faculty Of Engineering University Of Tokushima
-
MURAKAMI Riichi
Department of Mechanical Engineering, The University of Tokushima
-
YONEKURA Daisuke
Department of Mechanical Engineering, The University of Tokushima
-
SHIN Do
Department of Mechanical Engineering, The University of Tokushima
-
Shin Do
Department Of Mechanical Engineering The University Of Tokushima
-
Murakami Riichi
Department Of Mechanical Engineering The University Of Tokushima
-
Yonekura Daisuke
Department Of Mechanical Engineering The University Of Tokushima
-
Kim Yun-Hae
Department of Mechanical and Materials Engineering, Korea Maritime University
-
Yonekura D
Department of Mechanical Engineering, The University of Tokushima
-
Shin DH
Department of Mechanical Engineering, The University of Tokushima
関連論文
- Robust Control of Wind-induced Vibration for Suwon Observation Tower
- IS-7 Effect of VEGF Polymorphisms on Survival in Patients with Early Cervical Cancer(Group1 Oncology1,International Session)
- IS-15 Adjuvant Concurrent Chemoradiotherapy-Induced Neutropenia as a Prognostic Indicator of Treatment in Cervical Cancer(Group2 Oncology1,International Session)
- Alternate-Phase RZ Pulse Sequence Generation Using a Rational Harmonic Mode-Locked Fiber Ring Laser(Transmission Systems and Technologies, Recent Progress in Optoelectronics and Communications)
- A Game Theoretic Power Control Algorithm with Sequential Subchannel Nulling for Wireless Networks
- Clinical Significance of Aortic Knob Width and Calcification in Unstable Angina
- Multi-Cell MIMO Cooperation for OFDM-Based Broadcast Services and Its Outage Probability
- Slippage Mechanism of Pediatric Spondylolysis : Biomechanical Study Using Immature Calf Spines
- P-IS-34 A Clinical Study of Borderline Malignant Tumors of the Ovary(Oncology 9,Group 96,International Session)
- Evaluation of Adhesive Behaviors of Chromium Nitride Coating Films Produced by Arc Ion Plating Method