A Computer-Aided-Design Technique for Design of a Six-Section Elliptic Tire-Building Drum
スポンサーリンク
概要
- 論文の詳細を見る
In this investigation, a computer-aided-design method for a six-section elliptic tire-building drum is presented instead of the traditional geometric construction. The mathematical formulation of the proposed CAD technique is discussed in some detail. The efficient recursive equality-constrained quadratic programming method for solving constrained optimization problems is introduced to synthesize the mechanism of the drum. One practical problem is solved to illustrate the method.
- 一般社団法人日本機械学会の論文
- 1989-12-15
著者
-
IWATSUBO Takuzo
Department of Mechanical Engineering, Faculty of Engineering, Kobe University
-
Iwatsubo Takuzo
Faculty Of Engineering Kobe University
-
Iwatsubo Takuzo
Department Of Mechanical Engineering Kobe University
-
FENG Keqi
Faculty of Engineering, Kobe University
-
Feng Keqi
Faculty Of Engineering Kobe University
関連論文
- Novel Principle of Mechanical Energy Dissipation : Part 2-Dynamic Performances of Colloidal Damper
- Simulation of Fracture Healing Using Cellular Automata : Influence of Operation Conditions on Healing Result in External Fixation
- Condition Monitoring and Diagnosis System of Rotating Machinery
- Analysis of Transient Sound Energy Flow in Impact Noise
- A Study on the Dynamic Characteristics of Pump Seal : 1st Report, In case of Annular Seal with Eccentricity
- Wear Characteristics of a Novel Bearing System for Artificial Knee Joint : Micro-Pocket-Covered Femoral Component and Tibial Poro-Elastic-Hydrated Cartilage
- A Study upon Durability of the Artificial Knee Joint with PVA Hydrogel Cartilage
- Analysis of Golf Impact Phenomenon and Ball Trajectory
- Non-Linear Vibration Analysis of Rotor System Using Substructure Synthesis Method : Analysis with Consideration of Non-Linearity of Rotor
- Reliability Analysis of Structures under Seismic Excitation : Part III : Comparison of reliabilities obtained by first passage failure method and cumulative damage failure method
- Reliability Analysis of Structures under Seismic Excitation : Part II : Reliability by cumulative damage failure method
- Reliability Analysis of Structures under Seismic Excitation : Part I : Response ratio of structure having bi-linear spring behavior
- Novel Principle of Mechanical Energy Dissipation : Part 1-Static Performances of Colloidal Damper
- Suppression Phenomena of Resonant Oscillations in Strongly Nonlinear Systems due to Additional Asynchronous Excitations
- Asynchronous Stabilization Phenomena of Resonant Oscillations in Nonlinear Systems
- Obtaining a Model and Control for a Rigid Body Motion System : (Obtaining Inertia Parameters of a Rigid Body and Electromagnetic Characteristics for a Magnetic Levitation System)
- A Computer-Aided-Design Technique for Design of a Six-Section Elliptic Tire-Building Drum
- Rotordynamic Analysis of Submerged Motor Pumps : Influence of Long Seal on the Stability of Fluid Machinery
- Experimental Study of Dynamical Charateristics of a Long Annular Seal (In the Case of Concentric Rotor and Outer Cylinder)
- Coupled Lateral-torsional Vibration of Rotor System Trained by Gears : part 1. Analysis by Transfer Matrix Method
- Selection of Satisfactory Fundamental Solution in Boundary Value Inverse Analysis by B.E.M.
- Detection of the Point Where Rubbing Occurs in a Multisupported Rotor System
- Balancing of Flexible Rotors by Using Flexible Bearing Pedestals
- Balancing of Flexible Rotors
- Reliability Design of the Piping System against Earthquake Excitation
- The Study of Nonlinear Vibration Analysis of Rotor System Using Component Mode Synthesis Method(Analysis Using the Harmonic Balance Method)