325 マグネシウム合金の疲労特性に及ぼす環境の影響(OS1-5 環境・高温および熱疲労)(OS1 高強度材・表面改質材の疲労と破壊)
スポンサーリンク
概要
- 論文の詳細を見る
- 一般社団法人日本機械学会の論文
- 2001-07-19
著者
-
Miyashita Y
Nagaoka Univ. Technol. Nagaoka
-
Miyashita Yukio
Department Of Mechanical Engineering Nagaoka Univ. Of Technology
-
Sajuri Z
長岡技科大 大学院
-
Sajuri Zainuddin
Department Of Mechanical Engineering Nagaoka Univ. Of Technology
-
Mutoh Yoshiharu
Department Of Mechanical Engineering Nagaoka Univ. Of Technology
-
Xu Jinquan
Department of Mechanical Engineering, Nagaoka Univ. of Technology
-
Xu Jinquan
Department Of Mechanical Engineering Nagaoka Univ. Of Technology
-
MUTOH Yoshiharu
Department of Material Science, Nagaoka University of Technology
関連論文
- Time-dependent Fracture Mechanics Approach to Crack Growth of Solder
- Low Cycle Fatigue Behavior and Mechanisms of a Lead-free Solder 3.5Ag/96.5Sn(Electronic Devices)
- YBa_2Cu_3O_ Angle Grain Boundary Junction on Si Bicrystal Substrate
- Diffusion Bonding of Y-Ba-Cu-O High-T_c Superconductors
- Singularity at the Interface Edge of Bonded Transversely Isotropic Piezoelectric Dissimilar Materials
- Interface Fatigue Crack Propagation in Ceramic Thermal Barrier Coatings
- An Evaluation of the Adhesive Strength of the Interface between a Coating and Substrate
- 133 Cohesive Strength at the Interface Between Coating and Substrate
- 129 Effect of Environment on Fretting Fatigue Strength of Cast Al-Si Aluminum Alloy
- 312 CONTROL OF INTERMETALLIC PHASE FORMATION AT THE INTERFACE OF STEEL/ALMINUM DISSIMILAR METALS LASER LAP JOINT BY USING A BACKING PLATE
- Subsurface Crack Propagation in Rolling Contact Fatigue of Sintered Alloy
- 131 Subsurface Crack Propagation in Rolling Contact Fatigue of Sintered Alloy
- 514 Interface Fatigue Crack Propagation in Ceramic Thermal Barrier Coatings
- 409 Fretting Fatigue Design Curve based on Stress Distribution at the Contact Edge for Automotive steel
- On the Equivalent Thickness of a Side-Grooved Specimen
- 613 マグネシウム合金の疲労特性における応力比の影響(GS.F-3 疲労)
- 425 AZ61マグネシウム合金押出材の疲労メカニズム(軽量化・高強度化材料(1))
- 325 マグネシウム合金の疲労特性に及ぼす環境の影響(OS1-5 環境・高温および熱疲労)(OS1 高強度材・表面改質材の疲労と破壊)
- E-1 Thermal Shock Failure in Tungsten-10%Rhenium by Laser Irradiation Method(Session: Thermal Fatique/Creep)
- Stress Field near the Contact Edge in Fretting Fatigue Tests(Special Issue on strength and Fracture, and Experimental Mechanics)
- Effect of Relative Slip Amplitude on Fretting Fatigue Behavior of Silicon Nitride
- Mechanisms of Fretting Fatigue
- 130 Effect of Residual Stress on Fretting Fatigue Crack Propagation and Fatigue Strength
- Stress Field near the Contact Edge in Fretting Fatigue Tests(Tribology)
- Diffusion Bonding of Bi-Pb-Sr-Ca-Cu-O High-T_c Superconductors
- Stress Singularity at the Edge of Fiber/Matrix Interface
- 232 Al_2O_3-based Composite with BaTiO_3 Sintered by Spark Plasma Sintering
- J0403-3-2 Fretting Fatigue Strength Prediction of Dovetail Joint Based on Tangential Stress Range : Compressive Stress Range Diagram
- GS0304 Fretting Fatigue Strength and Life Prediction based on Stress distribution at the Contact Edge
- A Method for Determining Elastic-Plastic Stress Singularity at the Interface Edge of Bonded Power Law Hardening Materials(Stress Analysis)
- Effects of Dissolved Oxygen on Fatigue Characteristics of Austenitic Stainless Steel in 0.9wt% Sodium Chloride Solutions
- Effect of Underlay Stiffness on Cutting Profile of Polycarbonate Sheet during Wedge Indentation Process
- Failure Behavior of Sensitized SUS304 Stainless Steel with Small Surface Pre-Crack under Constant Load Condition in Simulated BWR Environment
- Fatigue Crack Growth Characteristics of Epoxy Resin Reinforced by Silica Particles at Elevated Temperature
- The Tightening Characteristics of Magnesium Alloy Bolts
- Dissimilar Materials Micro Welding between Stainless Steel and Plastics by Using Pulse YAG Laser
- Computational Investigation on Molten Pool of Single and Twin Beam Laser Welding
- Influence of Second Phase Particle on Fatigue Crack Growth Behavior in Ferrite Matrix Steels
- 818 STUDY ON RELIABILITY OF PB FREE Sn-Ag-Cu SOLDER JOINT