プラズマ浸炭硬化粉末焼結ローラの面圧強さに及ぼすショットピーニングの影響(ショット投射速度,ショット粒径およびショット硬さの影響)(機械要素,潤滑,工作,生産管理など)
スポンサーリンク
概要
- 論文の詳細を見る
In order to investigate the influence of shot peening on the surface durability of sintered powder metal rollers, the plasma case-hardened sintered powder metal rollers shot-peened with different shot velocity, shot diameter and shot hardness were fatigue tested under a sliding rolling contact condition. The compressive residual stress, the hardness and the surface roughness of the rollers increased and the pores in those were deformed by the shot peening. The failure mode of the rollers was spalling. The failure depth of most rollers agreed almost with the depth near the case-core boundary where the amplitude A(_τyz/HV) of the ratio of orthogonal shear stress to Vickers hardness became maximum. In these experiments the surface durabilities of strongly shot-peened rollers were lower than that of unpeened roller, on the other hand those of mildly shot-peened rollers were higher. The frictional force between the rollers and the shear stress below the contact surface generally increase as the surface roughness of the rollers increases. Therefore, it could be followed from above that the mild shot peening which dose not cause too large surface roughness should be selected in order to improve the surface durability of sintered rollers.
- 一般社団法人日本機械学会の論文
- 2002-04-25
著者
-
關 正憲
岡山大学工学部機械工学科
-
吉田 彰
岡山大学工学部
-
大上 祐司
香川大
-
鳥野 勇
住友金属工業(株)
-
大上 祐司
香川大学工学部
-
佐藤 雅靖
日本輸送機械(株)
-
大上 祐司
香川大学工学部知能機械システム工学科
-
烏野 勇
住友金属工業(株)
-
荒瀧 拓之
(株)永谷園
-
佐藤 雅靖
岡山大学大学院
関連論文
- 911 新軸受鋼製スラスト軸受の転がり疲れ強さ(機素潤滑設計II)
- D値と硬さを考慮したピッチング寿命と面圧強さの評価
- D値と硬さを考慮したピッチング寿命と面圧強さの評価(機械要素,潤滑,設計,生産加工,生産システムなど)
- 918 WC/C膜を施した浸炭硬化歯車のピッチング強さ(模索潤滑設計IV)
- ピーニングされた表面の摩擦・摩耗特性(S45C焼入れ材の場合)
- 1214 ショットピーニングを施した粉末焼結ローラの面圧強さ(面圧強度・疲労強度,一般講演)
- 104 シングルショットピーニングとダブルショットピーニングを施した鋼ローラの面圧強さ(OS02-1 歯車の強度I)
- 1001 ショットピーニングを施した粉末鍛造ローラの面圧強さ(機素潤滑設計III)
- 911 ダブルショットピーニングを施した鋼ローラの面圧強さに関する基礎的研究(機素潤滑設計I)
- 2003年度YME海外派遣報告(2) : 設計工学技術国際会議DETC2003への参加とゼネラルモータース歯車センターへの訪問報告