Spreadsheet Modelling of Grain Size Evolution during Rod Rolling
スポンサーリンク
概要
- 論文の詳細を見る
An analysis was conducted of the pass-by-pass evoution of austenite grain size during the rod rolling of plain carbon steel. This was achieved by organizing previously-developed equations relating grain size and hot working parameters into a commercial computer spreadsheet program. By considering the substantial "redundant" strains developed during rod rolling, the analysis reveals that metadynamic recrystallization (MRX) is the dominant microstructural process, and this is confirmed by the mill grain size measurements reported previously. The spreadsheet was also employed to examine the effects of modifications to rod rolling practice aimed at refining the austenite grain size. Little benefit is obtained by increasing the strain rate or by reducing the distance from the final rolling pass to the laying head. On the other hand, increasing the cooling rate on the forced-air cooling deck should lead to measurable grain refinement. Lowering the temperature during rolling can lead to even more refinement, and various strategies to achieve this are discussed.
- 社団法人 日本鉄鋼協会の論文
- 1996-06-15
著者
-
Jonas J.
Department Of Metallurgical Engineering Mcgill University
-
Maccagno T.
Department Of Metallurgical Engineering Mcgill University
-
Hodgson P.
Bhp Research Melbourne Laboratories
-
Jonas J.
Department Of Materials Engineering Mcgill University
-
MACCAGNO T.
Department of Chemical and Materials Engineering, University of Alberta
関連論文
- Effect of Alloying Elements on the Microstructure and Texture of Warm Rolled Steels
- Mathematical Modeling of Mean Flow Stress during the Hot Strip Rolling of Nb Steels
- Mathematical Modeling of the Mean Flow Stress, Fractional Softening and Grain Size during the Hot Strip Rolling of C-Mn Steels
- Influence of Ferrite Rolling Temperature on Microstructure and Texture in Deformed Low C and IF Steels
- TEM Characterization of the Recrystallization Behaviour of Warm Rolled Low Carbon Steels Containing Chromium during the Early Stages of Annealing
- Influence of Ferrite Rolling Temperature on Grain Size and Texture in Annealed Low C and IF Steels
- Effect of Deformation and Cooling Rate on the Microstructures of Low Carbon Nb-B Steels
- Mathematical Modelling of Mean Flow Stress during the Hot Strip Rolling of Multiply-alloyed Medium Carbon Steels
- Distinctive Aspects of the Physical Metallurgy of Warm Rolling
- Modelling the Thermomechanical and Microstructural Evolution During Rolling of a Nb HSLA Steel
- Prediction of Interpass Softening from the Strain Hardening Rate Prior to Unloading
- Hot Deformation Characteristics of Si-Mn TRIP Steels with and without Nb Microalloy Additions
- Modelling Texture Change during the Static Recrystallization of a Cold Rolled and Annealed Ultra Low Carbon Steel Previously Warm Rolled in the Ferrite Region
- Dynamic Strain Aging and the Wire Drawing of Low Carbon Steel Rods
- Spreadsheet Modelling of Grain Size Evolution during Rod Rolling
- The Influence of Bainite on Retained Austenite Characteristics in Si-Mn TRIP Steels
- Kinetics and Critical Conditions for the Initiation of Dynamic Recrystallization in 304 Stainless Steel
- FEM Simulation of Deep Drawing of Textured Aluminum Sheets Using Anisotropic Fourth-Order Strain-Tate Potential
- Static and Dynamic Strain Aging at High Temperatures in 304 Stainless Steel
- Effect of Silicon on the Interaction between Recrystallization and Precipitationin Niobium Microalloyed Steels
- Effect of Initial Grain Size on the Static Recrystallization Kinetics of Nb Microalloyed Steels
- Static Recrystallization of Nb and Nb-B Steels under Continuous Cooling Conditions
- Ultrasonic Prediction of r-value in Deep Drawing Steels.
- Gibbs energies of formation of TiS and Ti4C2S2 in austenite.
- Effect of Controlled Rolling on Texture Development in a Plain Carbon and a Nb Microalloyed Steel.
- Influence of Dynamic Recrystallisation on the Tensile Ductility of Steels in the Temperature Range 700 to 1150.DEG.C..