Deep Drawability of Electro-deposited Pure Iron Having an Extremely Sharp <111>//ND Texture
スポンサーリンク
概要
- 論文の詳細を見る
Electro-deposited pure iron having an extremely sharp ‹111›//ND fiber texture has extraordinarily excellent deep drawability. The relaxed constraints models based on Taylor theory cannot predict such high r-values. This excellent deep drawability seems to arise not only from the sharp ‹111›//ND texture but also significantly from the specific morphology of the microstructure, i.e. needle-shaped fine grains elongated in the normal direction.
- 社団法人 日本鉄鋼協会の論文
- 2008-05-15
著者
-
Yoshinaga Naoki
Steel Research Labs., Nippon Steel Corp.
-
Sugiura Natsuko
Steel Research Laboratories, Nippon Steel Corporation
-
Ushioda Kohsaku
Technical Dev. Bureau Nippon Steel Corp.
-
HIWATASHI Shunji
Steel Research Laboratories, Nippon Steel Corporation
-
USHIODA Kohsaku
Steel Research Laboratories, Nippon Steel Corporation
-
KADA Osamu
Muroran R & D Lab., Nippon Steel Corporation
-
Kada Osamu
Muroran R & D Lab. Nippon Steel Corporation
-
Yoshinaga Naoki
Steel Res. Laboratories Nippon Steel Corp.
-
Hiwatashi Shunji
Steel Research Laboratories Nippon Steel Corporation
-
Sugiura Natsuko
Steel Res. Laboratories Nippon Steel Corp.
-
Ushioda Kohsaku
Steel and Coil Research Lab., Nippon Steel Corporation
関連論文
- Comparison of the Dislocation Density in Martensitic Steels Evaluated by Some X-ray Diffraction Methods
- Incomplete Recrystallization and Subsequent Microstructural Evolution during Intercritical Annealing in Cold-rolled Low Carbon Steels
- Factors Affecting Texture Memory Appearing through α→γ→α Transformation in IF Steels
- Deep Drawability of Electro-deposited Pure Iron Having an Extremely Sharp //ND Texture
- The Effect of S and Mn on the High-temperature Oxidation and Scale Spallation Behavior of Low-carbon Steels
- Analysis of Flange Wrinkle in Square-shell Deep Drawing of Anisotropic Sheet
- Evolution of Dislocation Structure and Fatigue Crack Behavior in Fe-Si Alloys during Cyclic Bending Test
- Cold-rolling and Recrystallization Texture Formation in Electro-deposited Pure lron with a Sharp and Homoqeneous γ-fiber
- Comparison of the Dislocation Density in Martensitic Steels Evaluated by Some X-ray Diffraction Methods
- Role of TiAl_3 Fine Precipitate in Nucleation of the Primary Al Dendrite Phase during Solidification in Hot-Dip Zn-11%Al-3%Mg-0.2%Si Coated Steel Sheet
- Incomplete Recrystallization and Subsequent Microstructural Evolution during Intercritical Annealing in Cold-rolled Low Carbon Steels
- Recrystallisation of Ti IF Steel Investigated with Electron Back-scattering Pattern (EBSP)
- Texture Evolution of IF Steel Due to Recrystallization
- Blistering Behavior during Oxide Scale Formation on Steel Surface
- The Increase in a Brittle-to-ductile Transition Temperature in Fe-Al Single Crystals
- Influence of Si Addition to the Coating Bath on the Growth of the Al-Fe Alloy Layer in Hot-dip Zn-Al-Mg Alloy-coated Steel Sheets
- Role of Hematite Formation on Blister Generation during High Temperature Oxidation of Steel
- Influences of manganese on internal friction and carbon solubility determined by combination of infrared absorption in ferrite of low-carbon steels.
- Effect of Carbide Size Distribution on the Impact Toughness of Tempered Martensitic Steels with Two Different Prior Austenite Grain Sizes Evaluated by Instrumented Charpy Test
- Behavior of High-Temperature Embrittlement and Its Mechaism in Heat-Affected Zone of Low-Carbon Alloy Steels