The Effects of Operating Parameters on Micro-Droplet Formation in a Piezoelectric Inkjet Printhead Using a Double Pulse Voltage Pattern

スポンサーリンク

概要

• 論文の詳細を見る
• Japan Institute of Metalsの論文
• 2006-02-20

著者

• HWANG Weng-Sing

  Department of Materials Science and Engineering, National Cheng Kung University

• Lin Huey-jiuan

  Department Of Materials Science And Engineering National United University

• WU Hsuan-Chung

  Department of Materials Science and Engineering, National Cheng Kung University

• SHAN Tzu-Ray

  Department of Materials Science and Engineering, National Cheng Kung University

• Hwang W‐s

  National Cheng Kung Univ. Tainan Twn

• Hwang Weng-sing

  Department Of Material Science And Engineering National Cheng Kung University

• Shan Tzu-ray

  Department Of Materials Science And Engineering National Cheng Kung University

• Wu Hsuan-chung

  Department Of Materials Science And Engineering National Cheng Kung University

• Wu Hsuan-chung

  Department Of Materials Engineering And Center For Thin Film Technologies And Applications Ming Chi

関連論文

• Numerical Study of Fluid Flow Behaviors in an Alkali-Free Glass Melting Furnace
• Effects of Graphite, SiO_2, and Fe_2O_3 on the Crushing Strength of Direct Reduced Iron from the Carbothermic Reduction of Residual Materials
• Numerical Study of Fluid Flow and Heat Transfer Behaviors in a Physical Model Similar in Shape to an Actual Glass Melting Furnace and Its Experimental Verification
• The Effects of Operating Parameters on Micro-Droplet Formation in a Piezoelectric Inkjet Printhead Using a Double Pulse Voltage Pattern
• Study of Micro-Droplet Behavior for a Piezoelectric Inkjet Printing Device Using a Single Pulse Voltage Pattern
• Simulation of Droplet Ejection for a Piezoelectric Inkjet Printing Device
• Effects of Process Conditions of Melting Furnace on Alkali-Free Glass Cleanliness
• Electrochemistry of Ethanol Oxidation on Ni-Pt Alloy Electrodes in KOH Solutions
• Experimental Investigation on Earing Behavior of Aluminum/Copper Bimetal Sheet
• The Simulation of Shape Evolution of Solder Joints during Reflow Process and Its Experimental Validation
• Characterization of SnO_2/TiO_2 Double-Layer Films as Alcohol Sensing Materials
• Effects of Solid Fraction on the Heat Transfer Coefficient at the Casting/Mold Interface for Permanent Mold Casting of AZ91D Magnesium Alloy
• Mold Filling Analysis in Lost Foam Casting Process for Aluminum Alloys and Its Experimental Validation
• Multi-phase Flow Simulations in Direct Iron Ore Smelting Reduction Process
• Influence of Interfacial Structure Development on the Fracture Mechanism and Bond Strength of Aluminum/Copper Bimetal Plate
• Dielectric Properties and Leakage Current Characterization of the Ba(Sn_xTi_)O_3 Thin Films Prepared by Radio Frequency Magnetron Sputtering
• Forging Condition for Removing Porosities in the Hybrid Casting and Forging Process of 7075 Aluminum Alloy Casting
• Mathematical Modeling of Fluid Flow Phenomena during Tundish Filling and Subsequent Initial Casting Operation in Steel Continuous Casting Process
• Effects of Substrate Temperature and Oxygen Pressure on Crystallographic Orientations of Sputtered Nickel Oxide Films
• Effect of Film Thickness on Structural and Electrical Properties of Sputter-Deposited Nickel Oxide Films
• Effects of Basicity and FeO Content on the Softening and Melting Temperatures of the CaO-SiO_2-MaO-Al_2O_3 Slag System
• High Mechanical Properties of Polychloroprene/Montmorillonite Nanocomposites
• Transformation Characterization of Ni(OH)_2/NiOOH in Ni-Pt Films Using an Electrochemical Quartz Crystal Microbalance for Ethanol Sensors
• Numerical Simulation on Hardness Distribution for a FC250 Gray Cast Iron Brake Disc Casting and Its Experimental Verification
• Process Design Optimization through Numerical Experimentation for a Brake Disc Casting
• Effects of Pulse Voltage on the Droplet Formation of Alcohol and Ethylene Glycol in a Piezoelectric Inkjet Printing Process with Bipolar Pulse
• A Three Dimensional Cellular Automaton Model for the Prediction of Solidification Morphologies of Brass Alloy by Horizontal Continuous Casting and Its Experimental Verification
• Pasty Ranges and Latent Heat Release Modes for Sn-9Zn-xAg Lead-free Solder Alloys
• Numerical Simulation of Inclusion Removal in a Billet Continuous Casting Mold Based on the Partial-cell Technique
• Mathematical Modeling of Solidification Microstructure of Pure Copper by Vacuum Continuous Casting and Its Experimental Verification
• Study of Solid Accretion Formation inside Pyrometallurgical Vessels by a Wax Model and Similarity Conversion for Gas Bottom-Blown Process
• Preparation and Mechanical Properties of Polychloroprene–Montmorillonite Composites
• Dispersibility of Amphibious Montmorillonite
• Growth of Carbon Nano-Tubes from Electric-Arc-Furnace Dust Directly
• The Analysis of Molten Steel Flow in Billet Continuous Casting Mold
• A Modified Free Surface Treatment for the Modeling of Puddle Formation in Planar Flow Casting Process
• Effects of Actuating Pressure Waveforms on the Droplet Behavior in a Piezoelectric Inkjet

もっと見る 閉じる

スポンサーリンク