Mold Filling Analysis in Lost Foam Casting Process for Aluminum Alloys and Its Experimental Validation
スポンサーリンク
概要
- 論文の詳細を見る
- Japan Institute of Metalsの論文
- 2003-10-01
著者
-
HWANG Weng-Sing
Department of Materials Science and Engineering, National Cheng Kung University
-
Hwang Weng-sing
Department Of Materials Science And Engineering National Cheng Kung University
-
Hwang Weng-sing
Department Of Material Science And Engineering National Cheng Kung University
-
KUO Jer-Haur
Department of Materials Science and Engineering, National Cheng Kung University
-
Kuo Jer-haur
Department Of Materials Science And Engineering National Cheng Kung University
-
CHEN Jui-Ching
Department of Materials Science and Engineering, National Cheng Kung University
-
PAN Yung-Ning
Department of Mechanical Engineering, National Taiwan University
-
Pan Yung-ning
Department Of Mechanical Engineering National Taiwan University
-
Pan Yung-ning
Department Of Mechanical Engineering National Taiwan University Taipei
-
Chen Jui-ching
Department Of Materials Science And Engineering National Cheng Kung University
関連論文
- Numerical Study of Fluid Flow Behaviors in an Alkali-Free Glass Melting Furnace
- Effects of Graphite, SiO_2, and Fe_2O_3 on the Crushing Strength of Direct Reduced Iron from the Carbothermic Reduction of Residual Materials
- Numerical Study of Fluid Flow and Heat Transfer Behaviors in a Physical Model Similar in Shape to an Actual Glass Melting Furnace and Its Experimental Verification
- The Effects of Operating Parameters on Micro-Droplet Formation in a Piezoelectric Inkjet Printhead Using a Double Pulse Voltage Pattern
- Study of Micro-Droplet Behavior for a Piezoelectric Inkjet Printing Device Using a Single Pulse Voltage Pattern
- Simulation of Droplet Ejection for a Piezoelectric Inkjet Printing Device
- Effects of Process Conditions of Melting Furnace on Alkali-Free Glass Cleanliness
- Electrochemistry of Ethanol Oxidation on Ni-Pt Alloy Electrodes in KOH Solutions
- Experimental Investigation on Earing Behavior of Aluminum/Copper Bimetal Sheet
- The Simulation of Shape Evolution of Solder Joints during Reflow Process and Its Experimental Validation
- Characterization of SnO_2/TiO_2 Double-Layer Films as Alcohol Sensing Materials
- Effects of Solid Fraction on the Heat Transfer Coefficient at the Casting/Mold Interface for Permanent Mold Casting of AZ91D Magnesium Alloy
- Mold Filling Analysis in Lost Foam Casting Process for Aluminum Alloys and Its Experimental Validation
- Multi-phase Flow Simulations in Direct Iron Ore Smelting Reduction Process
- Influence of Interfacial Structure Development on the Fracture Mechanism and Bond Strength of Aluminum/Copper Bimetal Plate
- Forging Condition for Removing Porosities in the Hybrid Casting and Forging Process of 7075 Aluminum Alloy Casting
- Microstructures and Mechanical Behaviors of Ti-30Nb-1Fe-χHf Alloys
- Composition/Phase Structure and Properties of Titanium-Niobium Alloys
- Mathematical Modeling of Fluid Flow Phenomena during Tundish Filling and Subsequent Initial Casting Operation in Steel Continuous Casting Process
- Effects of Substrate Temperature and Oxygen Pressure on Crystallographic Orientations of Sputtered Nickel Oxide Films
- Effect of Film Thickness on Structural and Electrical Properties of Sputter-Deposited Nickel Oxide Films
- Effects of Basicity and FeO Content on the Softening and Melting Temperatures of the CaO-SiO_2-MaO-Al_2O_3 Slag System
- High Mechanical Properties of Polychloroprene/Montmorillonite Nanocomposites
- Transformation Characterization of Ni(OH)_2/NiOOH in Ni-Pt Films Using an Electrochemical Quartz Crystal Microbalance for Ethanol Sensors
- Numerical Simulation on Hardness Distribution for a FC250 Gray Cast Iron Brake Disc Casting and Its Experimental Verification
- Process Design Optimization through Numerical Experimentation for a Brake Disc Casting
- Effects of Pulse Voltage on the Droplet Formation of Alcohol and Ethylene Glycol in a Piezoelectric Inkjet Printing Process with Bipolar Pulse
- Effect of O_2-Plasma Treatment on Surface Characteristics and Osteoblast-Like MG-63 Cells Response of Ti-30Nb-1Fe-1Hf Alloy
- Enhancement of Biocompatibility on Bioactive Ti-Nb-Based Alloy by High-Density Plasma Modification
- Effects of Chemical and Heat Treatments on Surface Characteristics and Biocompatibility of Titanium-Niobium Alloys
- A Three Dimensional Cellular Automaton Model for the Prediction of Solidification Morphologies of Brass Alloy by Horizontal Continuous Casting and Its Experimental Verification
- Pasty Ranges and Latent Heat Release Modes for Sn-9Zn-xAg Lead-free Solder Alloys
- Numerical Simulation of Inclusion Removal in a Billet Continuous Casting Mold Based on the Partial-cell Technique
- Mathematical Modeling of Solidification Microstructure of Pure Copper by Vacuum Continuous Casting and Its Experimental Verification
- Study of Solid Accretion Formation inside Pyrometallurgical Vessels by a Wax Model and Similarity Conversion for Gas Bottom-Blown Process
- Preparation and Mechanical Properties of Polychloroprene–Montmorillonite Composites
- Dispersibility of Amphibious Montmorillonite
- The Analysis of Molten Steel Flow in Billet Continuous Casting Mold
- A Modified Free Surface Treatment for the Modeling of Puddle Formation in Planar Flow Casting Process