Estimation of Diameter of Granule Prepared by Spray Drying of Slurry with Fast and Easy Evaporation
スポンサーリンク
概要
- 論文の詳細を見る
In our previous report, a hollow granule model was proposed as a basis of spray drying granulation of slurry in case of fast and easy evaporation. In the present research, the compatibility of the model was examined by comparing the granule diameters obtained from the model with those from granulation experiments. The granules were prepared with slurry of 0.3 μm mono-dispersed silica particles without binder and dispersant by means of a spinning disk. As a result, it was confirmed that the calculated values from the model suited well with the experimental ones, and thus the granule diameter increases with lower rate of disk rotation and higher particle volume concentration of the slurry.
- 社団法人 化学工学会の論文
- 2002-09-01
著者
-
Shinohara K
Division Of Materials Science And Engineering Graduate School Of Engineering Hokkaido University
-
Liang Hua
Division Of Materials Science And Engineering Graduate School Of Engineering Hokkaido University
-
SHINOHARA KUNIO
Division of Materials Science and Engineering, Graduate School of Engineering, Hokkaido University
-
MINOSHIMA Hironori
Environment and Energy Department, Hokkaido Industrial Research Institute
-
MATSUSHIMA Keiichiro
Environment and Energy Department, Hokkaido Industrial Research Institute
-
Shinohara Kunio
Division Of Material Science And Engineering Graduate School Of Engineering Hokkaido University
-
Minoshima H
Environment And Energy Department Hokkaido Industrial Research Institute
-
Matsushima Keiichiro
Environment And Energy Department Hokkaido Industrial Research Institute
関連論文
- Quantitative Characterization of Microstructure of WC-Co/TiC-Al_2O_3 Composite Materials with Relate to Mechanical Properties
- New Design of Microstructure of WC-Co/TiC-Al_2O_3 Composite Materials by Mechanical Coating of Particles
- Particle flow model in a spouted bed
- Formation of a sigmoidal release pattern of core particles coated with layers of soluble and permeable particles
- Multiple-Layer Coating of Solids with Impermeable Film Dispersing Permeable Particles for Controlled Release
- Effect of the Porous Structure of a Coating Layer on the Release Rate of Core Particle
- Controlled Release of Core Particle Coated with Soluble Particles in Impermeable Layer
- Mechanical and Thermal Properties of Hot-Pressed Compact of Si_3 N_4 Particles Coated with AIN by CVD
- Estimation of Diameter of Granule Prepared by Spray Drying of Slurry with Fast and Easy Evaporation
- Basic Model of Spray Drying Granulation
- Preparation of large agglomerates of high voidage from charcoal particles for liquid absorption and release
- Agglomerating fluidization of group C particles : major factors of coalescence and breakup of agglomerates
- Density segregation of a binary solids mixture during batch operation in a two-dimensional hopper
- Segregation indices of multi-sized particle mixtures during the filling of a two-dimensional hopper
- Mechanism of particle shape modification by dry impact blending
- Air pressure drop across a particle moving bed in a three-dimensional cold model of a blast furnace
- Comparison of moving bed reactors for chemical vapor deposition coating of fine particles
- Hot Hardness of WC-Co/TiC-Al_2O_3 Composite Materials
- NO Adsorption Characteristics of Agglomerated Zeolite Particles
- Modeling of CVD Coating Inside Agglomerate of Fine Particles
- Size segregation of multicomponent particles during the filling of a hopper
- Image Blurring by Thermal Diffusion in the Observation of Hydrated Biomolecules with Soft X-Ray Microscopy
- Preparation of New WC-Co/TiC-Al_2O_3 Composite Materials with Mechanically Coated Particles