Effects in Surface Free Energy of Sputter-Deposited MoNx Films

スポンサーリンク

概要

• 論文の詳細を見る

• MoNx thin films have attracted much attention for semiconductor IC packaging molding dies and forming tools due to their excellent hardness, thermal stability. MoNx thin films with MoN0.57, MoN0.96, MoN1.48, MoN2.07, MoN2.44 were prepared using radio frequency (RF) sputter. The experimental results showed that the contact angle at 20 °C go up with raising N2 content to 106.4° at beginning, corresponding to MoN2.07, and then drop off. In addition, the contact angle components decreased with increasing surface temperature. Because increasing surface temperature disrupts the hydrogen bonds between water and the films and water vaporize gradually. The total surface free energy (SFE) at 20 °C decreases with N2 content to raise to 33.8 mN/m (MoN2.07) at the start, and then increases. Because a larger contact angle means that a weaker hydrogen bonding, resulting in a lower SFE. The polar SFE component has same trend with total SFE, but the dispersive SFE component is on the contrary exactly. The polar SFE component is also lower than the dispersive SFE component. This is resulting from hydrogen bonding being polar. The total SFE, dispersive SFE, and polar SFE of MoNx films decreased with increasing surface temperature. This is because water evaporation on the surface, disrupted hydrogen bonds and surface entropy increasing with increasing temperature.

• Published by the Japan Society of Applied Physics through the Institute of Pure and Applied Physicsの論文
• 2007-10-15

著者

• Fan Chun-wei

  Department Of Materials Science And Engineering National Cheng Kung University

• Lee Shih-chin

  Department Of Material Science Engineering National Cheng Kung University

• Fan Chun-Wei

  Department of Materials Science and Engineering, National Cheng Kung University, Tainan 70146, Taiwan

関連論文

• Influences of γ" and δ Precipitations on the Microstructural Properties of 718 Alloy through HIP, Solid-Solution, and Different Aging Heat Treatments
• Effects of Annealing Temperature on the Properties of Strontium Copper Oxide Prepared by Radio Frequency Reactive Magnetron Sputtering Method
• Properties of Strontium Copper Oxide Films Prepared by Radio Frequency Reactive Magnetron Sputtering with Different Oxygen Partial Pressures
• Surface Free Energy of Alloy Nitride Coatings Deposited Using Closed Field Unbalanced Magnetron Sputter Ion Plating
• The Influence of Canning HIP Treatment on the Microstructure Characters of Cr35-Si65 and Cr50-Si50 Targets
• Effects of HIP Treatment on the Microstructure and Properties of Cr35-Si65 Target
• Effect of Shot Peening Treatment on Forging Die Life
• Effects of HIP Treatment on the Microstructure of Cr50-Si50 Target
• Improvement in the Microstructure and Tensile Properties of Inconel 718 Superalloy by HIP Treatment
• Influences of Soaking Time in Hot Isostatic Pressing on Strength of Inconel 718 Superalloy
• Surface Free Energy Effects in Sputter-Deposited WN_x Films
• Wear Characteristics of a Laser Surface Alloyed Al-Mg-Si with Co Alloy Powder
• Microstructure and Characteristic of Laser Surface Alloyed Ni and Ni-Cr-B-Si on Al-Mg-Si Alloy
• Correlation between sp^2/sp^3 Ratio or Hydrogen Content and Water Contact Angle in Hydrogenated DLC Film
• ATR-FTIR and Nanoindentation Measurements of PMDA-ODA Polyimide Film under Different Curing Temperature
• Spin-Coating Polyimide Film on Hydrogenated DLC Film Surface Prepared by Ion Beam Deposition Method
• Photo-Catalytic Activity of Different Thicknesses TiO_2/SnO_2 Double Layer Nano Composite Thin Films
• Effects in Surface Free Energy of Sputter-Deposited MoNx Films

もっと見る 閉じる

スポンサーリンク