The Influence of Canning HIP Treatment on the Microstructure Characters of Cr35-Si65 and Cr50-Si50 Targets
スポンサーリンク
概要
- 論文の詳細を見る
- Japan Institute of Metalsの論文
- 2009-04-01
著者
-
CHANG Shih-Hsien
Department of Materials and Mineral Resources Engineering, National Taipei University of Technology
-
LEE Shih-Chin
Department of Materials Science and Engineering, National Cheng Kung University
-
Lee Shih-chin
Dep. Of Materials Sci. And Engineering National Cheng Kung Univ.
-
Lee Shih-chin
Department Of Materials Science And Engineering National Cheng-kung University
-
Lee Shih-chin
Department Of Material Science Engineering National Cheng Kung University
-
Chang Shih-hsien
Department Of Materials And Mineral Resources Engineering National Taipei University Of Technology
-
Chang Shih-hsien
Assab Steel Taiwan
-
TAM Chung-Hung
Department of Materials Science and Engineering, National Cheng Kung University
-
Tam Chung-hung
Department Of Materials Science And Engineering National Cheng Kung University
-
Chang Shih-hsien
Department Of Materials Science And Engineering National Cheng Kung University
関連論文
- Influences of γ" and δ Precipitations on the Microstructural Properties of 718 Alloy through HIP, Solid-Solution, and Different Aging Heat Treatments
- Effects of Annealing Temperature on the Properties of Strontium Copper Oxide Prepared by Radio Frequency Reactive Magnetron Sputtering Method
- Properties of Strontium Copper Oxide Films Prepared by Radio Frequency Reactive Magnetron Sputtering with Different Oxygen Partial Pressures
- Surface Free Energy of Alloy Nitride Coatings Deposited Using Closed Field Unbalanced Magnetron Sputter Ion Plating
- Optimization of Pressure and Soaking Time of HIP Treatment on 713LC Cast Superalloy
- The Influence of Canning HIP Treatment on the Microstructure Characters of Cr35-Si65 and Cr50-Si50 Targets
- Effects of HIP Treatment on the Microstructure and Properties of Cr35-Si65 Target
- Effect of Shot Peening Treatment on Forging Die Life
- Effects of Particle Size on Mechanical Properties of a TiC Containing Tool Steel by Hot Isostatic Press
- Effects of HIP Treatment on the Microstructure of Cr50-Si50 Target
- Improvement in the Microstructure and Tensile Properties of Inconel 718 Superalloy by HIP Treatment
- Influences of Soaking Time in Hot Isostatic Pressing on Strength of Inconel 718 Superalloy
- Microstructure and Mechanical Properties of 440C-TiC Composite Steels Produced through Powder Metallurgy Processing
- Surface Free Energy Effects in Sputter-Deposited WN_x Films
- Improvement of Aluminum Erosion Behavior and Corrosion Resistance of AISI H13 Tool Steel by Oxidation Treatment
- Enhancement of Erosion Resistance on AISI H13 Tool Steel by Oxynitriding Treatment
- Wear Characteristics of a Laser Surface Alloyed Al-Mg-Si with Co Alloy Powder
- Microstructure and Characteristic of Laser Surface Alloyed Ni and Ni-Cr-B-Si on Al-Mg-Si Alloy
- Correlation between sp^2/sp^3 Ratio or Hydrogen Content and Water Contact Angle in Hydrogenated DLC Film
- ATR-FTIR and Nanoindentation Measurements of PMDA-ODA Polyimide Film under Different Curing Temperature
- Spin-Coating Polyimide Film on Hydrogenated DLC Film Surface Prepared by Ion Beam Deposition Method
- Photo-Catalytic Activity of Different Thicknesses TiO_2/SnO_2 Double Layer Nano Composite Thin Films
- Effects of γ' Precipitation on the Structure and Properties of 713LC Superalloy via HIP Treatment
- Effects of Thermal Erosion and Wear Resistance on AISI H13 Tool Steel by Various Surface Treatments
- Effects of Post-oxidizing Treatment on Melting Loss and Corrosion Resistance of Gas Nitrided AISI H13 Tool Steel
- Sintered Behaviors and Electrical Properties of Cr50Cu50 Alloy Targets via Vacuum Sintering and HIP Treatments
- Effects in Surface Free Energy of Sputter-Deposited MoNx Films
- Improvement of Mechanical and Electrical Properties on the Sintered Ni-50 mass% Cr Alloys by HIP Treatment