Dryout heat flux for core debris bed. (II) Effects of particle size mixing and coolant flow.:Effects of Particle Size Mixing and Coolant Flow
スポンサーリンク
概要
- 論文の詳細を見る
For gaining basic data of post-accident heat removal, coolability of degraded core debris bed was studied with emphases on the effects of particle mixing and coolant flow, as a sequel to the effects of system pressure and particle size in Part ( I ). A fuel debris bed with decay heat was simulated by steel ball particles induction-heated in a water-filled 50 mm I. D. pyrex glass cylinder. The system pressure was fixed at 0.1 MPa and the bed height at 8 cm. The particle diameters were 3.0, 2.0, 1.0, 0.7 and 0.3 mm. The mixture of 1.0 and 3.0 mm or 1.0 and 2.0 mm particles was used as the simulate debris bed.<BR>The dryout heat flux for a mixture bed agreed fairly well with the Lipinski's model when a simple average diameter weighted by number was taken as the equivalent diameter, the same as for homogeneous beds. This means that small size particles with large number govern the dryout. The dryout heat flux increases with mass flux of coolant flow, asymptotically approaching to the complete vaporization of coolant. Coolability of debris bed can be greatly improved by a small amount of flow, which is produced by natural convection due to boiling, when coolant can flow into the bed from the bottom.
- 一般社団法人 日本原子力学会の論文
著者
-
Yamaoka Nobuo
Department Of Nuclear Engineering Graduate School Of Engineering Osaka University
-
Miyazaki Keiji
Department Of Nuclear Engineering Graduate School Of Engineering Osaka University
-
INOUE Shoji
Department of Electric, Information and Energy Engineering, Graduate school of Engineering, Osaka Un
-
OHAMA Toshihiro
Department of Nuclear Engineering, Faculty of Engineering, Osaka University
-
MURAI Kenji
Department of Nuclear Engineering, Faculty of Engineering, Osaka University
関連論文
- Forced Convection Heat Transfer and Temperature Fluctuations of Lithium under Transverse Magnetic Fields
- Magnetically Guided Free Surface Annular Nak Flow Experiment
- Thinning Improves Surface-Soil Physical Properties of Coniferous Forest Plantations
- Magnetically Guided Free Surface Annular Nak Flow Experiment
- Heat transfer and temperature fluctuation of lithium flowing under transverse magnetic field.
- Temperature fluctuation of sodium in annular flow channel heated by single-pin with blockage.
- Dryout heat flux for core debris bed. III Mixture of intact fuel and particulated clad.:Mixture of Intact Fuel and Particulated Clad
- Film boiling characteristics of potassium droplets on heated plate.
- Thermal interaction of water droplet with molten tin.
- Natural convection heat transfer of liquid lithium under transverse and parallel magnetic fields.
- Cavitation in cylindrical liquid metal shell imploded for axial magnetic flux compression.
- Dryout heat flux for core debris bed. (I) Effects of system pressure and particle size.:Effects of System Pressure and Particle Size
- Pressure Transient and Bubble Growth in Incipient Boiling of Superheated Potassium
- Experimental Studies on Characteristics of Pressure Attenuation and Recovery to Saturation for Decompressive Disturbances in Low Pressurized Water
- Influence of Void and Velocity Variations on Two-Phase Liquid Metal MHD Induction Converter Characteristics
- Influence of Void and Flow Regime on Liquid Metal MHD Induction Generator Using Two-Phase Flow
- Incipient boiling of sodium in an annular channel heated by a single-pin with blockage.
- Dryout heat flux for core debris bed. (II) Effects of particle size mixing and coolant flow.:Effects of Particle Size Mixing and Coolant Flow
- Intensity and Propagation Velocity of Compression Shock Pulses in Low Pressure Steam-Water Medium
- Analysis of Two-Phase Liquid Metal MHD Induction Converter
- Redistribution of gaseous phase of liquid metal two-phase flow in a strong magnetic field.