J-1 MECHANICAL PROPERTIES MAPPING AROUND INTERFACE OF BONDED MATERIALS USING NANOINDENTATION(Session: Interface/FEM/CAE)
スポンサーリンク
概要
- 論文の詳細を見る
Nanoindentation tests have been applied to quantitative characterization of interfaces of bonded materials. Distributions of indentation hardness and Young's modulus on the material surface are precisely determined. Two kinds of bonded materials, a diffusion bonding of aluminum alloy and stainless steel and a spot welding of carbon steels, are used for specimens. It has been found that the intermetallic compound layer of 4μm produced at the interface of the diffusion bonding has higher mechanical properties than those of the base materials. Two-dimensional mapping of mechanical properties on the cross section of the spot welding has also successfully been performed.
- 一般社団法人日本機械学会の論文
- 2006-11-08
著者
-
Miyashita Yukio
Nagaoka National College Of Technology
-
Ihara Ikuo
Department Of Endodontics Pulp And Periapical Biology Tokyo Dental College
-
NISHIMURA Futoshi
Department of Mechanical and Electrical Engineering, Tokuyama College of Technology
-
Kuriyama Yuji
Department of Mechanical Engineering, Nagaoka University of Technology
-
Nii Naoki
Nagaoka National College of Technology
-
Tanekawa Yoshinori
Nagaoka National College of Technology
-
Nishimura Futoshi
Department Of Mechanical Engineering Nagaoka University Of Technology
-
Nishimura Futoshi
Department Of Mechanical And Electrical Engineering Tokuyama College Of Technology
-
Kuriyama Yuji
Department Of Mechanical Engineering Nagaoka University Of Technology
-
Ihara Ikuo
Department of Mechanical Engineering, Nagaoka University of Technology
関連論文
- Elastic Constant Determinations of SiC/NiP Composite Coating by Surface Acoustic Wave and Nano-indentation
- 435 Fatigue behavior of die-cast AM60 alloy under different environmental conditions
- 229 Effect of Fabricated Surface on Fretting Fatigue Strength
- 2306 Corrosion Fatigue Behavior of Extruded AZ31
- 114 Effect of Corrosive Environment on Fatigue Strength of Magnesium alloy AZ-61
- 113 Fatigue Strength of Fabricated Structure Steel
- Fatigue Behavior of SiC Fiber Reinforced SiC Matrix Composites(Composite 1)
- In-Situ Observation of Alumina Particles in Molten Aluminum Using a Focused Ultrasonic Sensor(Advanced Technology of Experimental Mechanics)
- Inclusions Detection in Molten Metals by Focused Ultrasounds
- 17-O-10 Effect of Stress on Second Harmonic Generation of TeO_2-Based Glass Ceramics
- Unusual Variant of the Anterior Cerebral Artery : Case Report
- Intra-abdominal Cyst Following Revision of Ventriculoperitoneal Shunt : Case Report
- Calcification of Pulp Canal Space after Replantation of Immature Rat Molars
- Elastic Constant Determinations of SiC/NiP Composite Coating by Surface Acoustic Wave and Nano-indentation
- In Situ Monitoring of Solid-Liquid Interface of Aluminum Alloy Using High-Temperature Ultrasonic Sensor
- Application of Air-Coupled Ultrasound to Noncontact Surface Roughness Evaluation
- Analysis for Stress Singularity Field at a Vertex in Three-Dimensional Bonded Structures
- Measurement of Ultrasonic Attenuation in Material Surface Layer by Spectroscopic Technique with Ultrasonic Reflectivity Measurement
- Noncontact Monitoring of Surface Temperature Distribution by Laser Ultrasound Scanning
- 533 Effect of Environment on Fatigue Properties of Anodized AM60 Die-Cast Mg Alloys
- Quantitative Evaluation of Two Kinds of Surface Roughness Parameters Using Air-Coupled Ultrasound
- Cerebellar Hemorrhage After Supratentorial Craniotomy : Report of Three Cases
- 232 Al_2O_3-based Composite with BaTiO_3 Sintered by Spark Plasma Sintering
- Study on Factors Controlling Low Cycle Fatigue Life
- J-1 MECHANICAL PROPERTIES MAPPING AROUND INTERFACE OF BONDED MATERIALS USING NANOINDENTATION(Session: Interface/FEM/CAE)
- Accuracy Evaluation of Surface Temperature Profiling by a Laser Ultrasonic Method (Special Issue : Ultrasonic Electronics)
- Improved Density and Mechanical Properties of a Porous Metal-Free Phthalocyanine Thin Film Isotropically Pressed with Pressure Exceeding the Yield Strength
- A Simple Method for Profiling Surface Temperature Distributions by Laser-Ultrasound
- Strength of Dissimilar Materials Joint between A5052 and PET Joined by Using Friction Stir Heating
- Quantitative Evaluation of Stress-Strain Curves by Spherical-Tip Nanoindentation with Variable Radius Method
- Study on a Controlling Method for Crack Nucleation and Propagation Behavior in Laser Cutting of Glass
- Quantitative Evaluation of One-Dimensional Temperature Distribution on Material Surface Using Surface Acoustic Wave
- Ultrasonic Monitoring of Internal Temperature Distribution in a Heated Material