Mechanical Behavior during SR-treatment of Welding Residual Stress Through the Thickness(Mechanics, Strength & Structural Design)
スポンサーリンク
概要
- 論文の詳細を見る
Welding residual stress often makes deteriorate quality of the welded joint. So, PWHT (post weld heat treatment) is usually carried out for the purpose of relaxation of welding residual stress and softening of the welded joint. In this paper, the mechanical behavior during SR (stress relief annealing), which is the most popular treatment among the PWHT, is elucidated based on the results of three-dimensional thermo-elasto-plasto-creep analysis. The main results are as follows: According to the results of three-dimensional creep analysis, at the early stage during SR-treatment, creep strain tends to be easily accumulated in weld metal and HAZ (heat affected zone). Therefore, stress relaxation is considerable in weld metal and HAZ. Welding residual stress is mainly relaxed in the heating stage. The configuration of the stress distribution does not change and plastic strain is not produced during SR-treatment. Predicting creep strain and stress during and after SR-treatment from the results of two-dimensional plane-deformation thermo-elasto-plasto-creep analysis, the accuracy depends upon how actually represents the distribution and the magnitude of welding residual stress, which is one of the mechanical measures represented the severity of mechanical condition. If the stress concentration such as a notch, defects of welding etc. exists in parallel with weld line, the accumulation of the creep strain component perpendicular to a notch becomes great, but the stress component in the same direction is hard to be relaxed. Then, in the case that the characteristic of stress relaxation is inferior in base metal, though creep strain is greatly accumulated in weld metal and HAZ, the stress component perpendicular to weld line is hard to be relaxed.
- 大阪大学の論文
著者
-
Kim Y‐c
Osaka Univ. Osaka Jpn
-
Kim You
Osaka University
-
Kim Y
Osaka University
-
Bang Han
Graduate Student Of Osaka University
-
YAMAKITA Teruhisa
Graduate student of Osaka University
-
Yamakita Teruhisa
Graduate Student Of Osaka University:(present Office)kawasaki Heavy Industry Co. Ltd.
関連論文
- Joint Characteristics of Dissimilar Materials Friction Welds (II) : In the Case of Titanium/Aluminium Welds(Mechanics, Strength & Structure Design)
- A Predicting Method of Welding Residual Stress Using Source of Residual Stress (Report I) : Characteristics of Inherent Strain (Source of Residual Stress)(Mechanics, Strength & Structural Design)
- Mechanical Behavior during SR-treatment of Welding Residual Stress Through the Thickness(Mechanics, Strength & Structural Design)
- Mechanical Characteristics of Repair Welds in a Thick Plate (Report II) : Validity of Two-dimensional Plane-deformation Analysis(Mechanics, Strength & Structural Design)
- Mechanical Characteristics of Repair Welds in Thick Plate (Report I) : Distributions of Three-dimensional Welding Residual Stresses and Plastic Strains and Their Production Mechanisms(Welding Mechanics, Strength & Design)
- Bending Strength of Rolled H Section Steel Welds Jointed by Newly Developed Flash Welding System(Mechanics, Strength & Structure Design)
- Features of Thermal Stress Generated by Welding & Cutting under Loading(Mechanics, Strength & Structure Design)
- Safety Evaluation of I-Girder Bridge Repaired by Welding(Mechanics, Strength & Structural Design)
- Tensile and Fatigue Properties of Large Structural Members by a Newly Developed Welding System(Mechanics, Strength & Structure Design, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Ultimate Strength of Outstanding Plates in Cruciform Columns Assembled from Dissimilar Steels(Mechanics, Strength & Structure Design)
- Buckling Characteristics of High Manganese Non-magnetic Steel and Carbon Steel Hybrid Cruciform Columns : Investigation for Applying Dissimilar Materials to Steel Structures (Report III)(Mechanics, Strength & Structure Design)
- Fatigue Strength of High Manganese Non-magnetic Steel and Carbon Steel Welded Butt Joints : Investigation for Applying Dissimilar Materials to Steel Structures (Report II)(Mechanics, Strength & Structure Design)
- Mechanical Properties of High Manganese Non-magnetic Steel and Carbon Steel Welded Butt Joints : Investigation for Applying Dissimilar Materials to Steel Structures (Repot I)(Mechanics, Strength & Structure Design)
- Production Mechanism of Out-of-Plane Deformation in Fillet Welding(Mechanics, Strength & Structure Design)
- Characteristics of Out-of-Plane Deformation and Residual Stress Generated by Fillet Welding(Mechanics, Strength & Structure Design)
- Joints Characteristics of Dissimilar Materials Friction Welds (I) : Titanium/AISI 304L Stainless Steel(Mechanics, Strength & Structure Design)
- Characterisation of Residual Stress and Plastic Strain in AISI304L Stainless Steel/Titanium Friction Welds(Mechanics, Strength & Structural Design)
- Measurement of Three-dimensional Welding Residual Stresses due to Electron Beam Welding(Welding Mechanics, Strength & Design)
- 13. Brittle Fracture Strength of Repair Weldments in Thick Plate
- Measuring Theory of Three-dimensional Residual Stresses Using a Thinly Sliced Plate Perpendicular to Welded Line(Welding Mechanics, Strength & Design)
- Dynamical Characteristics of Oblique Y-Groove Weld Cracking Test Specimen of Arbitrary Thickness(Welding Mechanics, Strength & Design)
- New Measuring Method of Axisymmetric Three Dimensional Residual Stresses Using Inherent Strains as Parameters(Welding Mechanics, Strength & Design)
- Restraint Stresses and Strains Due to Slit Weld in Rectangular Plate (Report II) : Effective Restraint Intensities of a Slit in a Thick Finite Plate(Welding Mechanics, Strength & Design)
- Characteristics of Restraint Stress-Strain of Slit Weld in a Finite Rectangular Plate and the Significance of Restraint Intensities as a Dynamical Measure(Welding Mechanics, Strength & Design)
- Analytical Calculation Method of Restraint Stresses and Strains due to Slit Weld in Rectangular Plates(WELDING MECHANICS, STRENGTH AND DESIGN)
- Restraint Stresses and Strains due to Slit Weld in Rectangular Plate (Report I) : Formulae for Conventional Restraint Intensities of a Slit in Finite Plate
- Generation and Reduction of Residual Stress in Ceramic/Metal Joints(Mechanics, Strength & Structural Design)
- Mathematical Treatment of Phase Transformation and Analytical Calculation Method of Restraint Stress-Strain(Welding Mechanics, Strength & Design)
- Mathematical Treatment of Phase Transformation and Analytical Calculation Method of Restraint Stress-Strain
- Effects of Initial Imperfections on Out-of-Plane Deformation and Residual Stress Produced by Welding(Mechanics, Strength & Structure Design)
- Welding of Steel Structures in Service Conditions(Mechanics, Strength & Structural Design)
- Prevention of HS-type Crack in Welding under Pulsating Loads(Mechanics, Strength & Structural Design)
- Prevention of Solidification Crack in Welding under Pulsating Loads(Mechanics, Strength & Structural Design)
- Insert Layer Design Using Residual Stress in Si_3N_4/Steel Joining as Parameter(Mechanics, Strength & Structural Design)
- Dynamical Aspect of Cold Cracking Parameter(Welding Mechanics, Strength & Design)
- Short-circuiting Transient Phenomena in GMA/CO_2 Welding (I) : Through-the-Wire Sensor for Feedback Torch Height Control(Physics, Processes, Instruments & Measurements)
- Restraint Stress and Strain in Circular Patch Welds(Mechanics, Strength & Structural Design)