Dimensional Change in Plastic Gears in Vacuum and Some Experimental Results
スポンサーリンク
概要
- 論文の詳細を見る
Because plastic gears possess sufficient self-lubricating ability, operation without lubrication is feasible. Accordingly, plastic gears seem to be most suitable for use in vacuum, where lubricating oil cannot be used. However, with plastic gears, there are also problems pertaining to heat resistance, the occurrence of dimensional change as the moisture contained in the atmosphere dehydrates in vacuum, and so on. For the purpose of applying plastic gears to practical use in vacuum, in this research, the dimensional change in vacuum of various plastic gears which were used in atmosphere was examined, a few operation tests were performed, and the results were investigated.
- 一般社団法人日本機械学会の論文
- 1993-12-15
著者
-
Maruyama H
Mitsubishi Electric Corp. Hyogo Jpn
-
Maruyama Hiroki
Department Of Applied Biological Chemistry Graduate School Of Agricultural And Life Sciences The Uni
-
TSUKAMOTO Naohisa
Department of Mechanical Engineering, Chiba Institute of Technology
-
Koyama Masaharu
Department of Mechanical Engineering, Chiba Institute of Technology
-
Chiba Kooki
Shinku Kikai Kogyo Co., Ltd.
-
Tsukamoto Naohisa
Department Of Mechanical Engineering Chiba Institute Of Techno1ogy
-
Koyama Masaharu
Department Of Mechanical Engineering Chiba Institute Of Technology
-
Chiba Kooki
Shinku Kikai Kogyo Co. Ltd.
関連論文
- Longitudinal Change in Renal Function in Patients With Idiopathic Dilated Cardiomyopathy Without Renal Insufficiency at Initial Diagnosis
- Fabry Disease Exhibiting Recurrent Stroke and Persistent Inflammation
- Investigation about the Strength of Plastic Gears : 5th Report; Abrasion of Nylon Gear due to the Difference in Materials of Mating Gears.
- Isolation of Abikoviromycin and Dihydroabikoviromycin as Inhibitors of Polyketide Synthase Involved in Melanin Biosynthesis by Colletotrichum lagenarium
- Clinical and Genetic Investigation of a Japanese Family With Cardiac Fabry Disease : Identification of a Novel α-Galactosidase A Missense Mutation (G195V)
- Development of Low-Noise Gears : Silencing Effect and Operating Characteristics of Polyamide Elastomer Gears
- A Study on Development of Low Noise Gears : Silencing Effect and Operation Characteristics of Nylon Gears Filled with Plasticizers
- Water Lubrication Characteristics of Polyacetal Gears Filled with Carbon Fibers
- Dimensional Change in Plastic Gears in Vacuum and Some Experimental Results
- Basic Characteristics of Plastic Gears Lubricated with Water
- A Study on Strength Design Methods for Plastic Gears : Estimation of Operation Life of Plastic Gears Elevated-Temperature Environment
- Fundamental Characteristics of Plastic Gears Made of Thermoplastic Resin Filled with Various Fibers
- A Study for the Development of Plastic Worm Gears : Plastic Worm Gears filled with Fiber and Solid Lubricant
- Investigation about the Prevention of Tooth Profile Change of Nylon Gears : 3rd Report, Wear and Tooth Profile Change in Profile Shifted Nylon Gears
- Investigation about the Prevention of Tooth Profile Change of Plastic Gears : 2nd Report; Abrasion and tooth profile change of nylon gears, reinforced with a stiffener
- Development of Plastic Gears for Power Transmission : Various Methods of Lengthening the Life of Plastic Gears and Their Effect
- Argument on Plastic Gears for Power Transmission
- Investigation about the Strength of Plastic Gears : 4th Report ; Abrasion and State of Tooth Profile Change of Driven Nylon Gear
- Investigation about the Strength of Plastic Gears : 1st Report, The Strength of Nylon Gears which have Counter-Crowning
- Investigation about the Strength of Plastic Gear : 2nd Report ; Abrasion of the Nylon Gear for Power Transmission, Meshing with the Steel Gear
- Noise and Transmission Efficiency under Deformation of Tooth Form of Nylon Gear
- Investigation about Load Capacity of Nylon Gears, When Tooth Surface Finishing of Mating Steel Gears is different. : 1st Report ; Results of Load Test at Cylinder
- Investigation about the Strength of Plastic Gears : 3rd Report ; Strength of the Nylon Gear meshing with the Steel Gear which was cut by Semitopping Hob
- Investigation about the Strength of Plastic Gears : 6th Report, Endurance Limit and Damage State of Nylon Gear for Power Transmission
- Investigation about the Prevention of Tooth Profile Change of Plastic Gears : 1st Report; Amount of Profile Modification of the Steel Gear, which Meshed with the Nylon Gear
- Investigation about Load Capacity of Nylon Gears, when Tooth Surface Finishing of Mating Steel Gears is different : 2nd Report; Abrasion of Nylon Gear Meshing with Ground Steel Gear