Investigation about the Strength of Plastic Gears : 5th Report; Abrasion of Nylon Gear due to the Difference in Materials of Mating Gears.
スポンサーリンク
概要
- 論文の詳細を見る
In the no lubricant operation, it is believed that a stainless steel gear, a brass gear and a cast iron gear are better applicable as the mating gears of nylon gears for rust prevention, than a carbon steel gear. But the abrasion of nylon gear when the nylon gear meshes with these gears is not clear, because these gears have been little used. In this report an abrasion experiment of nylon gear, which meshed with these three metallic gears, was performed. And the abrasion of nylon gear in this experiment was compared and examined with the abrasion of nylon gear in the earlier report, which meshed with the carbon steel gear. The abrasion of nylon gear when the nylon gear meshed with three different materials gears has been made clear.
著者
-
Tsukamoto Naohisa
Department Of Mechanical Engineering Chiba Institute Of Technology
-
Tsukamoto Naohisa
Department Of Mechanical Engineering Chiba Institute Of Techno1ogy
関連論文
- Investigation about the Strength of Plastic Gears : 5th Report; Abrasion of Nylon Gear due to the Difference in Materials of Mating Gears.
- Development of Low-Noise Gears : Silencing Effect and Operating Characteristics of Polyamide Elastomer Gears
- A Study on Development of Low Noise Gears : Silencing Effect and Operation Characteristics of Nylon Gears Filled with Plasticizers
- Water Lubrication Characteristics of Polyacetal Gears Filled with Carbon Fibers
- Dimensional Change in Plastic Gears in Vacuum and Some Experimental Results
- Basic Characteristics of Plastic Gears Lubricated with Water
- A Study on Strength Design Methods for Plastic Gears : Estimation of Operation Life of Plastic Gears Elevated-Temperature Environment
- Fundamental Characteristics of Plastic Gears Made of Thermoplastic Resin Filled with Various Fibers
- A Study for the Development of Plastic Worm Gears : Plastic Worm Gears filled with Fiber and Solid Lubricant
- Investigation about the Prevention of Tooth Profile Change of Nylon Gears : 3rd Report, Wear and Tooth Profile Change in Profile Shifted Nylon Gears
- Investigation about the Prevention of Tooth Profile Change of Plastic Gears : 2nd Report; Abrasion and tooth profile change of nylon gears, reinforced with a stiffener
- Development of Plastic Gears for Power Transmission : Various Methods of Lengthening the Life of Plastic Gears and Their Effect
- Argument on Plastic Gears for Power Transmission
- A Study on Strength Design Methods of Plastic Gears : 1st Report, Calculation Method of Fatigue Strength Due to Strain Energy : Series C : Vibration Control Engineering Engineering for Industry
- Investigation about the Strength of Plastic Gears : 4th Report ; Abrasion and State of Tooth Profile Change of Driven Nylon Gear
- Investigation about the Strength of Plastic Gears : 1st Report, The Strength of Nylon Gears which have Counter-Crowning
- Investigation about the Strength of Plastic Gear : 2nd Report ; Abrasion of the Nylon Gear for Power Transmission, Meshing with the Steel Gear
- Noise and Transmission Efficiency under Deformation of Tooth Form of Nylon Gear
- Investigation about Load Capacity of Nylon Gears, When Tooth Surface Finishing of Mating Steel Gears is different. : 1st Report ; Results of Load Test at Cylinder
- Investigation about the Strength of Plastic Gears : 3rd Report ; Strength of the Nylon Gear meshing with the Steel Gear which was cut by Semitopping Hob
- Investigation about the Strength of Plastic Gears : 6th Report, Endurance Limit and Damage State of Nylon Gear for Power Transmission
- Investigation about the Prevention of Tooth Profile Change of Plastic Gears : 1st Report; Amount of Profile Modification of the Steel Gear, which Meshed with the Nylon Gear
- Investigation about Load Capacity of Nylon Gears, when Tooth Surface Finishing of Mating Steel Gears is different : 2nd Report; Abrasion of Nylon Gear Meshing with Ground Steel Gear