模型船による波浪中航走時の船体強度に関する研究 : (第三報) 吃水及びトリムの影響について
スポンサーリンク
概要
- 論文の詳細を見る
On the problems of the dynamical strength of ships going in waves, especially on the problems of the slamming of ships, we have tried the experiments in the experimental tank by towing the six metre model ship, made of brass, and the influences of the wave lengths and heights were investigated in the former reports.In the present paper, the experiments on various ship draughts and trims when wave length and height are constant are investigated. From the experiments, the following principal conclusions may be drawn, (1) Slamming occurs as the encounter period of ship and wave T_e closes to the period of pitching and heaving coupled motion of ship Tph, and abates as it recedes.(2) The cause of slamming is due to the coupled motion of pitching and heaving, but pitching is preeminent.(3) The pitching angle, the maximum rise of bow, the phase lag between pitching and heaving, the phase lag between wave and pitching, all these factors have the important influences on the cause of ship slamming.(4) The statical pressure difference of the maximum and minimum bottom pressure at ship bow increases in the slamming zone.(5) The impact bottom pressure indicates the maximum value when d/L=0.0325,and the impact pressure ratio at ship bow amounts to 11.6.(6) The maximum impact bottom pressure changes linearly with the change of ship trim. It is given approximately as the following formula Max. ζ_0=11.0+176(Trim/L)(7) The mean hogging stress at deck, having no consideration for the impact stress due to slamming, shows a tendency to increase remarkably with the occurrence of slamming; while the mean sagging stress scarcely increases. This property is the same in any ship draughts and trims.(8) In slamming zone, the impact compressive stress is recognized on ship deck, and indicates the maximum value when d/L=0.0325. This impact stress also changes linearly with the change of ship trim.(9) The maximum ship draught which causes the slamming throughout all ship speeds is d_s/L=0.062.(10) The minimum ship speed which causes the slamming throughout all ship draughts is V_<ms>=0.54 M/sec (F=0.42). This value perfectly coincides with the value which were obtained in the wave length experiments.(11) By comparing the measured stresses with calculated ones, the effective wave height ratios η are obtained.(i) Hogging η_H indicates the maximum value when d/L=0.0325.(ii) Hogging η_H indicates the maximum value when even keel.(iii) Sagging η_S has a tendency to increase with increase in ship draught.(iv) Sagging η_S indicates the minimum value when even keel.(v) η in high speeds become fairly large compared with η in low speeds, while the increasing percentage of η owing to the Smith's correction are nearly the same, irrespective of ship speeds in any ship draughts and trims.
- 社団法人日本船舶海洋工学会の論文
著者
関連論文
- 進水時船體應力測定用電気計器の試作報告 : 計器小委員會報告第1報
- 初期撓みをもつ連続パネルの挫折強度と凹損
- T2-SE-A1タンカー模型による波浪中の船体曲げモーメントの研究(第1報) : 曲げモーメントの実験結果について
- 穂高山丸の航走中の船体応力頻度について
- 高張力鋼材を用いた薄板構造の挫屈および圧壊強度について
- 波浪と船体強度
- 溶接構造物の設計時におけるぜい性破壊の考慮
- 瘠馬が船底の凹入に及ぼす影響
- 切欠脆性における寸法効果
- 荒海中における船体縱応力の推定法
- 脆性亀裂の発生と伝播の理論とくにSOD試験について
- 脆性破壊伝播に関する研究(第3報) : スリットが定速で拡大する場合の応力場
- 船底縦通材貫通部の強度に関する研究
- 鋼材の切欠脆性に及ぼす塑性歪の影響
- 模型船による波浪中航走時の船体強度に関する研究
- 模型船による波浪中航走時の船体強度に関する研究 : (第三報) 吃水及びトリムの影響について
- 模型船による波浪中航走時の船体強度に関する研究
- 模型船による波浪中航走時の船体強度に関する研究 : (第二報) 波長の影響について
- 模型船に依る波浪中航走時の船体強度に関する研究
- 模型船による波浪中航走時の船体強度に関する研究(第一報)
- スランミング(船首底衝撃)と船の運動
- スランミングの実験から
- 船体縦通材の有効性に関する研究 : 第1報 基礎理論
- 水圧をうける矩形防撓板の塑性変形
- 脆性破壊伝播に関する研究(第2報) : 円孔が定速で拡大する場合の応力場の厳密解
- 脆性破壊伝播に関する研究(第1報)
- 脆性破壊の伝播に関する H 型切缺試驗