横割れの発生と残留応力, 拡散性水素濃度との関係 : 低温溶接後熱処理による 21/4Gr-1 Mo 鋼厚板突合わせ溶接部の横割れ防止について(第 1 報)
スポンサーリンク
概要
- 論文の詳細を見る
This research was conducted in order to clarify the cause of transverse cracks, which were observed in heavy section weldments by submerged arc process, and to investigate the possibility of prevention of them by use of low temperature postweld heat treatment. In the investigation, cracking tests were carried out on restraint test specimens with the thickness range of 50mm through 200mm. The characteristics of cracks were observed. Moreover, magnitude of residual stresses and concentration of diffusible hydrogen just after welding as well as after low temperature postweld heat treatment, both of which were considered to have close connection with the cause of the cracks, were measured experimentally and their effects on the occurrence of a crack were examined. The outline of the results obtained is as follows; (1) Transverse cracks initiate in the weld metals just below the final layer of welds and gradually propagate both to the top surface and to the bottom surface. Intergranular fracture generally appears in the initiation area of the crack and quasi-cleavage fracture appears in the propagation area. (2) The location of the largest residual stress parallel to the weld line corresponds to that of crack initiation and so does the location of the highest concentration of diffusible hydrogen just after welding. This implies that the transverse crack is a cold cracking induced by longitudinal residual stress and diffusible hydrogen. (3) The highest longitudinal residual stress is nearly constant in the range of plate thickness over 50mm. Meanwhile, the highest concentration of diffusible hydrogen just after welding increases with an increase in plate thickness. It decreases with an increase in interpass temperature during welding or in temperature of postweld heat treatment and thereby the cracks can be arrested. Judging from the result, prevention of these cracks can be made possible only by decreasing diffusible hydrogen concentration through postweld heat treatment under lower temperature as compared with a conventional intermediate stress relief annealing.
- 社団法人溶接学会の論文
- 1979-10-05
著者
関連論文
- 641 3Cr-1Mo 改良鋼の機械的性質と溶接性 : 石炭液化反応容器用鋼の開発 2(圧力容器 (1)(2)・低温用鋼, 材料, 日本鉄鋼協会第 107 回(春季)講演大会)
- 640 3Cr-1Mo 鋼の機械的性質に及ぼす合金元素の影響 : 石炭液化反応容器用鋼の開発 1(圧力容器 (1)(2)・低温用鋼, 材料, 日本鉄鋼協会第 107 回(春季)講演大会)
- 219 高耐食性Fe-Ni-Cr-Mo系合金溶接材料の研究(第2報) : 凝固割れ感受性に及ぼすC, Si, Ni, Cr, Moの影響
- 212 高耐食性Fe-Ni-Cr-Mo系合金溶接材料の研究(第1報) : 耐食性におよぼすC, Ni, Cr, Mo, の影響
- 211 溶接金属組織の水素割れ感受性
- 極厚板多層溶接部の応力除去焼なまし時における力学的挙動(溶接部のミクロ・フラクトグラフィ)
- 201 極厚板溶接部の残留応力およびSR時のその挙動
- 817 HIP により成形した粉末超合金の超塑性挙動と高温引張特性(超塑性, 萌芽・境界技術, 日本鉄鋼協会第 110 回(秋季)講演大会)
- 691 粉末製超合金タービンディスクの製造技術の開発 : AS HIP 法による超合金の機械的特性の把握(耐熱鋼・耐熱合金 (3), 材料, 日本鉄鋼協会第 109 回(春季)講演大会)
- 101 SiCウィスカ強化アルミニウム合金複合材料とアルミニウム合金の接合
- Ni基粉末超合金AF115の高温における疲労き裂伝ぱと疲労寿命の関係 : 弾塑性およびクリープひずみエネルギーパラメータ⊿W_fと⊿W_cを介して
- 218 Ni-Cr-Fe系肉盛溶接金属部の水素脆化特性について
- 121 オーステナイト系ステンレス鋼肉盛溶接部のK_IHの把握
- PS-22 2 1/4Cr-1Mo 鋼における焼もどし脆性と Acoustic Emission との関連(性質, 日本鉄鋼協会第 103 回(春季)講演大会)
- 454 AE計測における溶接割れ発生位置評定精度の向上
- 217 オーステナイト系ステンレス溶着金属部の水素脆化 (第4報)
- 213 遅れ破壊減少のAE計測に関する一考察
- 122 オーステナイト系ステンレス溶着金属部の水素脆化 (第3報)
- 121 オーステナイト系ステンレス溶着金属部の水素脆化 (第2報)
- 132 オーステナイト系ステンレス溶着金属部の水素脆化 (第1報)
- 131 圧力容器用鋼材の焼戻し脆化と水素脆化との関連
- 106 焼戻し脆性におよぼす前処理の影響 (第2報)
- (95) 高張力鋼の溶接割れに関する研究
- 419 超硬合金と鋼との接合(第2報) : インサート材の影響
- 336 超硬合金と鋼との接合(第1報) : 応力緩和材の影響
- 厚肉圧力容器ノズル部の溶接残留応力に関する研究(昭和61年度春季全国大会論文発表講演討論記録)
- 厚肉円筒の新しい軸対称残留応力測定法(昭和61年度春季全国大会論文発表講演討論記録)
- 厚肉圧力容器ノズル部の溶接残留応力に関する研究(昭和61年度春季全国大会論文発表講演論文)
- 厚肉円筒の新しい軸対称残留応力測定法(昭和61年度春季全国大会論文発表講演論文)
- 厚板の新しい軸対称残留応力測定法
- 圧力容器溶接時の低温溶接後熱処理による中間焼鈍の省略
- 415 圧力容器ノズル溶接部の溶接残留応力特性(第3報) : 継手形状と残留応力との関係
- 210 圧力ノズル溶接部の溶接残留応力特性(第2報) : 測定精度の確認
- 209 圧力容器ノズル溶接部の溶接残留応力特性(第1報) : 厚板3軸残留応力測定法の軸対称体への適用
- 248 ラグ類溶接時に予熱温度を保持するためのガス加熱条件 (第2報) : 予熱温度を保持するためのガス加熱条件と溶接条件との関係
- 247 ラグ類溶接時に予熱温度を保持するためのガス加熱条件 (第1報) : ガス加熱時の加熱冷却特性
- 127 Cr-Mo-V 鋼溶接部の再熱割れに関する研究
- 161 21/4Cr-IMo鋼溶接部の再熱割れに関する一考察
- 粉末冶金によるNi基超合金の再結晶および超塑性挙動
- Ni基超合金粉末のHIP固化材の機械的性質
- 209 SA508 Cl.3 鋼多層溶接HAZ部の横割れ防止について (第2報) : 割れ防止低温溶接後熱処理条件
- 208 SA508 Cl.3 鋼多層溶接HAZ部の横割れ防止について (第1報) : HAZのミクロ組織と割れ感受性との関係
- 横割れの発生と残留応力, 拡散性水素濃度との関係 : 低温溶接後熱処理による 21/4Gr-1 Mo 鋼厚板突合わせ溶接部の横割れ防止について(第 1 報)
- 123 厚板突合わせ溶接部のビード横割れに関する研究
- 仮付溶接部の拘束度と割れとの関連
- 120 仮付(断続)溶接部の拘束度と割れとの関連
- 21/4 Cr-1 Mo 鋼厚板溶接部の横割れ防止低温溶接後熱処理条件 : 低温溶接後熱処理による 21/4 Cr-1 Mo 鋼厚板突合せ溶接部の横割れ防止について(第 4 報)
- 低温溶接後熱処理時の水素濃度変化と処理条件との関係 : 低温溶接後熱処理による 21/4Cr-1Mo 鋼厚板突合せ溶接部の横割れ防止について(第 3 報)
- 水素濃度と溶接施工条件との関係 : 低温溶接後熱処理による 21/4 Cr-1 Mo 鋼厚板突合わせ溶接部の横割れ防止について(第 2 報)
- 116 直後熱処理による厚板突合わせ溶接部の割れ防止に関する研究(第2報) : 直後熱処理による溶接部水素量の低減と割れ防止
- 115 直後熱処理による厚板突合わせ溶接部の割れ防止に関する研究(第1報) : 溶接部の水素量と溶接施工条件との関係