Elasto-Plastic Bending of Thin Annular Plates
スポンサーリンク
概要
- 論文の詳細を見る
This paper is concerned with the analysis of the elasto-plastic bending of thin annular plates based on Mises' yield condition and Hencky's stress-strain relations. The fundamental equations for the purely elastic range are obtained from the usual ones by introducting a new variable representing the appearance of plastic state on the surface of plate, and the elastoplastic range is analysed by using the corresponding V.V. Sokolovsky's equations. Numerical calculation is performed for several combinations of edge conditions, loading conditions and the ratios of inner and outer radii. Propagation of the plastic range in the meridian section and distributions of the deflection and th components of bending moments for various magnitudes of load intensity are obtained for each case.
- 一般社団法人日本機械学会の論文
著者
-
Ohashi Yoshio
Faculty Of Engineering Nagoya University
-
Ohashi Yoshio
Faculty Of Engieering Nagoya University
-
MURAKAMI Sumio
Faculty of Engineering, Nagoya University
-
Murakami Sumio
Faculty Of Engineering Nagoya University
-
OHASHI Yoshio
Faculty of Engineering, Nagoya University
関連論文
- On Mechanism of Induced Plastic Anisotropy of Polycrystalline Metals
- Experimental Investigation on History-dependence of Plastic Behaviour of Brass under Combined Loading
- TIME DEPENDENT VARIATION OF THE DEFORMATION OF A STRIP WITH CIRCULAR HOLE UNDER CONSTANT COMPRESSIVE LOAD
- ELASTIC-VISCOPLASTIC DEFORMATION OF STRIP HAVING ANGULAR-NOTCH WITH CIRCULAR ROOT UNDER COMPRESSION
- On Bending of Thin Circular Plate with Nonlinear Stress-Strain Relation
- Elasto-Plastic Bending of Thin Annular Plates
- Large Elastoplastic Deflection of Thin Annular Plate
- Calibration Test in Photo-Rheological Stress Analysis for Variable Rate of Principal Stress Difference
- Calibration Test for a Photo-Rheological Method of Stress Analysis in the Plastically Flowing Body
- On the Elasto-plastic Bending of a Clamped Circular Plate under a Partial Circular Uniform Load
- Experiment on the Isoclinic Parameter Appearing in Elasto-Visco-Plastic Materials
- Effects of Block Height and Punch Width on Deformation of Elastic-Viscoplastic Block
- Stress-Strain Curve of Mild Steel in the Initial Stage of Cyclic Loading
- PLASTIC DEFORMATION OF MILD STEEL UNDER COMBINED LOAD OF AXIAL FORCE AND TORSION WITH STRAIN TRAJECTORIES OF CONSTANT CURVATURE#
- FORMULATION OF DEFORMATION BEHAVIOUR OF SOFTENED CELLULOID UNDER PROPORTIONAL LOADING BASED ON NON-LINEAR VISCOELASTIC THEORY
- PRECISE EXPERIMENTAL RESULTS AND AN ANALYTICAL FORMULATION OF THE SUBSEQUENT PLASTIC DEFORMATION OF MILD STEEL SUBJECTED TO PRE-STRESSING
- Effect of Front Tension on Strip Rolling Analysed by Photo-Rheological Method
- On Stress-Strain Relation of Mild Steel in Unloading and Inverse Loading for Bending Analysis of Thin Circular Plate
- Deformation of a Supported Long Cylindrical Shell of Aluminum Alloy under Internal Pressure
- A PRECISE STRESS-STRAIN RELATION OF MILD STEEL IN THE PROPORTIONAL DEFORMATION UNDER COMBINED LOADING
- Examination of Fatigue Failure of Metals by Means of Electro-Plating Method
- Application of the Extended Newton Method to the Steady-State Creep Analysis of Shells of Revolution
- Steady-State Creep of Circular Cylindrical Shells
- Transient Creep Analysis of Pressurized Circular Cylindrical Shells
- Effects of Hydrostatic Pressure and Material Anisotropy on the Transient Creep of Thick-Walled Tubes (the Transactions of the Japan Society of Mechanical Engineers) : Papers published in the Bulletin of the JSME are not included here