Experimental Study of Shear Spinning
スポンサーリンク
概要
- 論文の詳細を見る
Many researchers have done some work on the analysis of shear spinning process. But their works are limited to a certain extent. This paper deals with the experiment on the shear spinning process of aluminium to find out the fundamental characters in detail. The influence of the following working conditions is discussed ; roller position angle, clearance between roller and mandrel, feed of roller, cone angle, speed of rotation of mandrel, roller corner radius, roller diameter, blank thickness and blank diameter. In addition, the deformation theory of simple shear which is derived from the observation of the experiments, is checked about tangential force P_θ. It is said that there is an optimum blank thickness t_s, of which the calculated values agree with the experiments, and if the blank thickness is smaller than t_s, the theoretical value is overestimated, but underestimated, if it is the other way round.
- 一般社団法人日本機械学会の論文
著者
-
KUDO Hiroaki
Department of Media Science, Graduate School of Information Science, Nagoya University
-
Kudo Hiroaki
Department Of Metallurgy Yokohama National University
-
MUROTA Tadao
Department of Technology, Tokyo Institute of Technology
-
Murota Tadao
Department Of Mechanical Engineering Tokyo Institute Of Technology
-
HAYAMA Masujiro
Department of Metallurgy, Yokohama National University.
-
Hayama Masujiro
Department Of Metallurgy Yokohama National University
-
Hayama Masujiro
Department Of Industrial Metallurgy Faculty Of Engineering Yokohama National University
関連論文
- Multi-Objective Genetic Programming with Redundancy-Regulations for Automatic Construction of Image Feature Extractors
- Linear GP with Redundancy-removed Recombination for Synthesis of Image Feature Extraction Programs
- Linear GP with redundancy-removed recombination for synthesis of image feature extraction programs (数理モデル化と問題解決・バイオ情報学)
- Acceleration of Genetic Programming by Hierarchical Structure Learning : A Case Study on Image Recognition Program Synthesis
- On the Non-Uniform Deformation of Material in Axially Symmetric Compression Caused by Friction : Part 2, Theoretical Analysis of Compression of Circular Cylinder by the Finite Element Method
- On the Non-Uniform Deformation of Material in Axially Symmetric Compression Caused by Friction : Part 1, Comparsion of Results of Analysis Using Calculus of Variations with Experiments Concerning Compression of Cylinder
- On the Non-Uniform Deformation of a Block in Plane-Strain Compression Caused by Friction : Part 3, Analysis by Finite Element Method when Surface Sticks on Tool
- On the Non-Uniform Deformation of Block in Plane-Strain Compression Caused by Friction : Part 2,Experiments and Proposition of Relative Slip Ratio
- Lawn Weeds Detection Methods Using Image Processing Techniques
- On the Non-Uniform Deformation of a Block in Plane-Strain Compression Caused by Friction : Part 4, Analysis by Finite Element Method in General Conditions
- Theoretical Study of Shear Spinning
- Bifurcation of Crystalline Solutions and Freezing
- Deformation Modes and Wrinkling of Flange on Shear Spinning
- Experimental Study of Shear Spinning
- Multi-Objective Genetic Programming with Redundancy-Regulations for Automatic Construction of Image Feature Extractors
- The Fracture of Walls on Shear Spinning : Study on the Spinnability of Aluminium Plates
- On the Non-Uniform Deformation of Block in Plane-Strain Compression Caused by Friction : Part 1,Theoretical Analysis Using Calculus of Variations
- Estimation of Torque in Cold Forming of Internal Thread
- Study on Spinnability of Aluminum and It's Alloys
- On the Cold Rolling of Fin of the Air Cooling Pipe
- On the Strength of Cylindrical Shell and Multilayer Vessel under Impact Pressure Loading
- On the Study of Metal Spinning
- Analysis of Working Force in Shear Spinning of Cones
- Theoretical Analysis on Ring Rolling of Plain Ring
- Incorporating Top-Down Guidance for Extracting Informative Patches for Image Classification
- Calculation for Thread Rolling Pressure
- Estimation of Load and Contact width in Rotational Compression of Rod
- Study of Lubrication in Shear Spinning
- Theoretical Method for Estimation of Forces and Torque on Cross Rolling of Stepped Shaft
- Incorporating Contextual Information into Bag-of-Visual-Words Framework for Effective Object Categorization
- Evaluations of Feature Extraction Programs Synthesized by Redundancy-removed Linear Genetic Programming: A Case Study on the Lawn Weed Detection Problem
- Theoretical Study of Tube Spinning