Fatigue Strengths of Shafts with Press-fitted Collar

スポンサーリンク

概要

• 論文の詳細を見る

• Canti-lever type fatigue tests were carried out on press-fitted and related specimens of 50 mm dia. Results obtained were as follows : (1) The hardness of a collar had little effect on the fatigue limit of a press-fitted specimen. (2) If the collar was press-fitted by superposing over the fillet of shouldered shaft, the fatigue limit was lowered remarkably as compared with that in the case of press-fitting alone. (3) The fatigue limit of the press-fitted specimen was reduced even under very light press-fit pressures, and the press-fit pressure had little effect on the fatigue limit. (4) When the collar was press-fitted closely to the shoulder with a very sharp fillet, the fatigue limit was lowest but not lowered as compared with that of a shouldered specimen with a very sharp fillet.

• 一般社団法人日本機械学会の論文

著者

• Nishioka Kunio

  Central Research Laboratories

• KOMATSU Hideo

  Central Research Laboratories, Sumitomo Metal Industries. Ltd., Amagasaki.

• Komatsu Hideo

  Central Research Laboratories Sumitomo Metal Industries Ltd.

関連論文

• Fundamental Investigations of Fretting Fatigue : Part 3,Some Phenomena and Mechanisms of Surface Cracks
• Fundamental Investigations of Fretting Fatigue : Part 1,On the Relative Slip Amplitude of Press-fitted Axle Assemblies
• Fundamental Investigations of Fretting Fatigue : Part 4,The Effect of Mean Stress
• Fundamental Investigations of Fretting Fatigue : (Part 5,The Effect of Relative Slip Amplitude)
• Strength of Integral Pipe Flanges : No.2 Gasket Seating Stress and the Influence of Number of Bolts
• Strength of Integral Pipe Flanges : No.1 Stress Distribution in Flange and the Criticism of the Conventional Standards
• Research on the Reinforcement with a Rib : (5th Report, The Deformation of Structural Parts Reinforced with Ribs where the Cross Section of Intersecting Members is Equal)
• Researches on Increasing the Fatigue Strength of Press-Fit Axle : 2nd Report Press-Fitted Shaft Assembly Two Dimensional Photoelasticity
• Researches on Increasing the Fatigue Strength of Press-Fit Shaft : 4th Report, Geometry of the End of Press-Fitting and σ_< w1 >
• The Strength of Railroad Wheels : 1st Report, Thermal Stresses in Disc Wheels
• Research on the Reinforcement with a Rib : (6th Report, The Deformation of Structural Parts Reinforced with Ribs where the Cross Sections of Two Intersecting Members Are Different in Rigidity)
• Fatigue Strengths of Shafts with Press-fitted Collar
• The Effects of Metallurgical Factors on Fatigue Strengths : Part 1,The Effects of Carbon and the Relations between Static Strengths and Fatigue Strengths
• The Effects of Metallurgical Factors on Fatigue Strength : Part 3, The Effects of C, Si, Mn, P and Cu (2)
• Researches on Increasing the Fatigue Strength of Press-Fitted Shaft Assembly
• The Effects of Metallurgical Factors on Fatigue Strength : Part 4, The Effects of N and B
• The Effects of Metallurgical Factors on Fatigue Strength : Part 5, The Effects of Ni, Cr and Mo (1)
• The Effects of Metallurgical Factors on Fatigue Strength : Part 2, The Effects of C, Si, Mn, P and Cu (1)
• The Strength of Railroad Wheels : 2nd Report, The Effect of Wheel Contours on Thermal Stresses in Wheels
• A Fractographic Study of Fatigue Fracture of AISI 4340 Steel

もっと見る 閉じる

スポンサーリンク