金属材料の疲れにおける繰返し速度の影響
スポンサーリンク
概要
- 論文の詳細を見る
1. Preface When the metallic materials were broken down due to fatigue under repeated stresses, it was previously published partially that the repeating speeds had influences upon the fatigue-curves, especially the endurance limits. But they were not investigated systematically. The causes lay, it was though, in the fact that no reliable high speed fatigue testing machine was available. In this research, some carbon steels from 0^.07% to 0^.6% carbon has been studied under the new Nishihara type high speed fatigue testing machine, which was designed as satisfying the purposes, and also under the old Woler type fatigue testing machine, and some other materials were also studied. 2. Effects of the repeating speeds We have studied on the range from 5,000 rpm to 15,000 rpm by the new Nishihara type high speed fatigue testing machine, and studied on the range from 50 rpm to 2,000 rpm by the old Woler type fatigue testing machine. It was imperfectly known that the endurance limits were rising as the repeating speeds were rising. By this research, the facts that the endurance limits were rising as the repeating spceds were rising were confirmed, and these rates of the rising are different according to the contents of carbons or the internal crystal systems or the results of the heat treatment. When we consider all states of fatigue curve at the high stresses, the materials are fatigued sooner in the cases of repitition of high speed than of low speed, i. e. at the high stresses, the fatigue strengths are lower than at the low stresses, at the high speed repitition. But at the endurance limits, or at the lower stresses near such limits, the materials are fatigued sooner in the case of repitition of low speed than of high speed. As the cause that the fatigue strength is varied by such variations of the repeating speeds, we consider 2 causes. At the high stresses the facts that the fatigue strengths at the high speed repetitions are lower than at the low speed repetition, are considered as the next. The heat quantity which is accumlated in the material in unit time is much larger at high speed repetition than at lower speed repetition, and then the temperature of the material rises and the material is softened. So the strength becomes smaller. At the low stress near the endurance limits, the rising of temperature of the material is very much smaller, but on the contrary, the variations of the internal crystal system are larger at low speed repetition than at high speed repetition, so that the material at low speed repetition is fatigued sooner than at high speed repetition. 3. Conclusion To save the testing time of fatigue test, we perform the fatigue test under high speed repeating stresses. But by such a method, the phenomena, that the endurance limits were varied by the repeating speed, were discovered, and the facts that according to the internal crystal system of material, the rate of influences was different, was also discovered. we now believe that we must study another materials, ana discuss the effects of the repeating speed that influences the fatigue strength.
- 一般社団法人日本機械学会の論文
- 1951-11-20
著者
関連論文
- 空氣粉碎機内の氣流に関する研究
- 抛物線回轉面ダイスによる引抜きの研究
- ほう物線回轉面ダイスによる引抜の研究
- 捩り加工の捩り疲勞強さにおよぼす影響
- 非線型復原力を有する振動系の1/3分数調波振動について
- 初期ひずみおよび遊隙の組合せよりなる復元特性を有する振動系の強制振動について
- 疲れ破損の法則に関する研究
- 曲面接触におけるまだら摩耗耐久限度
- 階差法による正方形板撓みの解法
- 並んだ切欠を有する半無限平板における応力について
- 引張を受ける任意切欠(回転対称)を有する丸棒における應力分布について
- ねじ継手におけるねじ山荷重分布について
- ボルト頭部における應力集中と疲れ強さ
- ねじ山のたわみが非線型的である場合のねじ山荷重分布について
- 並んだ切缺を有する半無限板における應力について
- 自動制御系の検出部における乾性摩擦が系の安定度に及ぼす影響 : 液面および圧力制御回路
- 自動制御装置の管制部における非線型特性が制御機能に及ぼす影響
- 自動制御装置の管制部における非線型特性が制御機能に及ぼす影響
- 金属の内部摩擦の振動数による變化
- 壓縮せる粉體内の應力分布
- 高周波表面燒入せる鋼圓〓の轉り接觸耐久限度(創立50周年記念號)
- 繰返應力による殘留應力の變化のX線的研究
- 繰返變動應力に對する金屬材料の強さ
- 塑性域における輕金屬のX線的應力測定に關する研究
- 繰返し応力による内部摩擦の変化
- 繰返し応力による内部摩擦の変化
- 内部摩擦による弦の振動の減衰
- 金属の内部摩擦の振動数による変化(続報)
- 微小振幅における金屬の内部摩擦係數の測定
- 金属材料の疲れにおける繰返し速度の影響
- 空氣粉碎機による金屬粉末製造に關する研究
- 空氣粉碎機による金属粉末製造に関する研究(第2報)
- 鋼のねじり降伏について
- 球軸受の負荷理論におけるヘルツ式の修正
- 塑性域における軟鋼のX線的應力測定に關する研究
- 塗料によるひずみ測定
- 軟鋼の塑性變形における表面効果について