Bulk Temperature Rise of Working Tooth Flanks in Spur Gears : Vibration, Control Engineering, Engineering for Industry

スポンサーリンク

概要

• 論文の詳細を見る

• The bulk temperature rise was studied when a moving heat source with variational heat quantity was applied repeatedly at regular intervals to the surface of an isotropic and homogeneous rectangular shaped body used as a model of a spur gear tooth. The effect of radiation at the inner surface of a boss on the bulk temperature rise is reduced as the distance between the inner surface of the boss and the working tooth flank is increased. The bulk temperature rise is almost inversely proportional to the heat supply interval. The size of the heat supply region and the moving direction of the heat source scarcely affect the bulk temperature rise. in a |νν^^-| range of not less than 1000, the bulk temperature rise is not affected by the moving velocity of the heat source, and the approximate bulk temperature rise can be obtained by dividing the temperature rise of the working tooth flank due to a stationary heat source by the number of teeth.

• 一般社団法人日本機械学会の論文

著者

• Fujii Masahiro

  Faculty Of Engineering Okayama University

• FUJITA Komei

  Okayama University of Science

• OBATA Fumio

  Okayama University

• FUJII Masahiro

  Keihin Iron Works, Nippon Kokan K. K.

• Obata F

  Tottori Univ. Tottori Jpn

• Fujita K

  Honorary Professor Of Okayama University

関連論文

• Interference Detection Based on AIC Using EM Algorithm for UWB MB-OFDM Systems
• Effects of Tooth Profile on Scoring Behavior in Spur Gears
• Scoring in Spur Gear Pairs (2nd Report, Scoring Temperatures in Case of EP Oils) : Series C : Vibration, Control Engineering, Engineering for Industry
• Scoring in Spur Gear Pairs (Increase in Scoring Load Capacity Due to Tooth Profile Wear on the Approach Side) : Vibration, Control Engineering, Engineering for Industry
• Flach Temperature in Spur Gears : Series C : Vibration, Control Engineering, Engineering for Industry
• Bulk Temperature Rise of Working Tooth Flanks in Spur Gears : Vibration, Control Engineering, Engineering for Industry
• Effects of Load Intensity Fluctuation on Anti-seizure Capacities of Lubricating Oils : 2nd Report, Anti-seizure Capacity of Gear Base Oil at a High Specific Sliding
• Effects of Load Intensity Fluctuation on Anti-seizure Capacities of Lubricating Oils : 1st Report, States of Interference amonF Projections in Case of Gear Base Oil
• Temperature Rise of a Spur Gear Tooth Due to Repeated Action of a Moving Heat Source
• Scoring in Spur Gear Pair : 1st Report, Scoring Temperature in Case of Gear Base Oil
• Study on the Anti-seizure Capacities of EP Oils by Two Cylinder Test
• Effect of Hardened Depth on Fatigue Strength of Carbonitrided Gears
• Effect of Standard Pressure Angle on the Fatigue Strength of Nitrided Gears
• Effect of Hardened Depth on the Fatigue Strength of Nitrided Gears
• A Study on the Effect of Tooth Fatigue on the Dynamic Performance of a Gear Pair (In the Case of Nitrided Aluminium Chromium Molybdenum Steel Gears) : Vibration, Control Engineering, Engineering for Industry
• Effects of Hardened Depth and Relative Radius of Curvature on Surface Durability of a Nitrided SACM645 Steel Roller
• Effects of Surface Roughness on the Seizure Limits of Lubricating Oils : 2nd Report, In the Case of EP Oils
• Study on the Scoring Resistance of Lubricating Oil in Two Cylinder Test : 3rd Report, Seizure Behavior under Rolling-sliding Contact Condition and the Relation between Seizure and Temperature in Non-EP Gear Oil

もっと見る 閉じる

スポンサーリンク