回転機固定子巻線の導体と絶縁物の間の力の伝達機構の検討
スポンサーリンク
概要
- 論文の詳細を見る
In order to obtain the fundamental knowledge in clarifying thermal stress induced in the stator windings, the interaction mechanism between the conductor and insulation of the stator windings under axial load were examined theoretically and experimentally. The stress analysis was made with the aid of the equivalent model in which the stator windings was regarded as composite structure consisting of the conductor and the insulation bonded by the adhesive. The experiments were carried out on six different kinds of model windings and the strain distributions induced on the insulation surface were measured by strain gauges under axial load. The electrical properties, such as tangent delta and breakdown voltage, were also measured under axial load and the variations in the electrical properties caused by the occurrence of mechanical damages were examined. The results obtained are as follows : (1) The interaction mechanism between the conductor and insulation of the stator windings followed the derivation shown in the stress analysis. (2) When the axial load was applied, the tensile stress in the insulation was maximum at the center portion and the shearing stress in the adhesive was maximum at the end portion. Therefore, it was considered that the insulation windings should bear not only the tensile strength of insulation but also the shearing strength of the adhesive or of the insulation in the vicinity of the adhesive. (3) The closed relationship existed between the occurrence of mechanical damages and the variations in the electrical properties. That is, the apparent variations were observed in the tangent delta characteristics when bonding failures took place in the adhesive and the remarkable reductions were observed in breakdown voltages when the insulation was broken.
- 社団法人日本材料学会の論文
- 1975-06-15
著者
関連論文
- 短絡時の回転機固定子巻先端部の変形挙動と強度
- 回転機固定子巻線の繰返し曲げ荷重下における変形ならびに破壊挙動
- 回転機固定子巻線の曲げ変形ならびに破壊挙動
- 回転機固定子巻線の導体と絶縁物の間の力の伝達機構の検討
- 衝撃荷重を局部的に受ける場合の発泡スチロールの動的圧縮応力-ひずみ特性
- 発泡スチロールの衝撃による圧縮応力─ひずみ特性
- 接着形抵抗線ひずみゲージの補強効果に関する一考察
- 熱サイクルによる回転機固定子巻線の破壊機構
- 多翼ファンの設計技術に関する研究 : 第1報,定常回転時に羽根に生じる応力の発生メカニズム
- 積層円筒の変形とすべり挙動
- 積層円筒の変形とすべり挙動
- テープと接触するヘッドの摩耗形状に関する研究 : 第2報, 解析法の検討
- テープと接触するヘッドの摩耗形状に関する研究 : 第1報, 実験的検討
- 多翼ファンの設計技術に関する研究 : 第2報,軸系のねじり振動モデルの基礎的検討
- 期待される新エネルギー
- デザインテクノロジーの必要性
- 超伝導材料, 堂山昌男, 山本良一(編), 伊原英雄, 戸叶一正(著), 1987年, 東京大学出版会発行, A5判, 350ページ, 3200円
- 1986年, Kokon Shoin発行, 150x230mm, 897ページ, 20,000円(粉体小特集)
- 設計のエキスパート化に伴う材料強度評価技術の在り方
- 325 回転機固定子巻線用含浸レジンの接着強度の半実験的解析法による検討