Fe-Si 合金の高温塑性変形におよぼす結晶粒径と Si 含有量の影響
スポンサーリンク
概要
- 論文の詳細を見る
The effect of grain size on the tensile defomation behaviour of 1 and 3wt%Si-Fe alloys was studied over the temperature range from 25° to 800℃ at strain rates of 10^<-5> and 1 1/sec. The relations between the grain size and yield stress or flow stress at a given strain in both alloys were approximately represented by the Hall-Petch equation over the experimental range. The yield behaviour in both alloys was discussed to be separated into the following four temperature regions ; (1) the low temperature deformation region below 300℃, (2) the athermal deformation region between 300° and 500℃, (3) the region of yielding phenomenon between 500° and 700℃, and (4) the high-temperature deformation region above 700℃. The value of friction stress for yielding, σ_0, and its temperature and strain rate sensitivities in the region (3) increased with increasing Si content. For both alloys was also observed a new yielding phenomenon in the region (3). The apparent activation energy for this yielding was unchanged with Si content and about 93kcal/mol, and the activation area was changed with it, i. e. 170-200 b^2 in 1% Si alloy and 70-100 b^2 in 3% Si alloy. The grain size dependnce of flow stress in the regions (3) and (4) was comlicated with the change of temperature and strain. This behaviour was explained qualitatively in terms of the modified work hardening model. The change in steady-state or maximum flow stress, σ_M, with Si content was almost the same to that of σ_0, and then the internal stress developed during deformation, σ_i (≃σ_M-σ_0) was considered to be nearly constant regardless of the Si content. These results indicated that the high-tmeperature deformation mechanism in the two Si alloys was different from that of pure iron, and during the deformation the dislocation glide was considered to play an important role.
- 社団法人日本鉄鋼協会の論文
- 1977-08-01
著者
関連論文
- 170 ねじり変形による数種の金属の定常状態変形に関する研究(転炉・熱間加工, 製鋼・加工, 日本鉄鋼協会第 77 回(春季)講演大会講演)
- 158 衝撃ねじり試験におけるオーステナイト 18・8 ステンレス鋼, 17Cr 鋼および極軟鋼の変形抵抗の温度・歪速度依存性(加工, 製鋼加工, 日本鉄鋼協会 第 76 回(秋季)講演大会)
- 熱間衝撃ねじり試験による鋼の変形抵抗の測定(講演論文特集号)
- 133 熱間衝撃ねじり試験による鋼の変形抵抗の測定(均熱炉・部会報告講演・熱間加工, 加工, 日本鉄鋼協会第 73 回(春季)講演大会講演)
- 186 軟鋼の高ひずみ変形抵抗の温度依存性および加工軟化現象について(性質・加工, 加工・性質, 日本鉄鋼協会第 72 回(秋季)講演大会講演論文集 (II))
- 133 断続衝撃ねじり試験による 13 Cr 鋼の熱間加工性の研究(加工・熱処理, 日本鉄鋼協会第 69 回春季講演大会講演論文集 (II))
- 大ひずみ加工AZ31マグネシウム合金の超塑性変形
- マグネシウム合金AZ31の降温中多軸鍛造に伴う微細粒組織の生成と超塑性特性
- 超微細粒マグネシウム合金AZ31の低温超塑性変形に及ぼす異方性の影響
- 超微細粒マグネシウム合金AZ31の低温超塑性挙動と組織変化