<Note>Properties of Particleboard from Lesser-used Species I. : Albizia falcata Backer
スポンサーリンク
概要
- 論文の詳細を見る
この論文は国立情報学研究所の学術雑誌公開支援事業により電子化されました。Flakeboards in the density range of 0.4-0.65 g/cm^3 were produced using Albizia falcata as raw material and a urea formaldehyde resin, a phenol-melamine formaldehyde resin, and an isocyanate compound as adhesives. Mechanical properties and dimen sional stability of boards were determined. Using long flakes from this low-density species, high MOE and MOR was obtained in relatively low-density board. Further improvements in internal bond strength and the dimensional stability in thickness direction may enable to produce boards sufficient for structural use. Isocyanate bonded board showed superior properties to those bonded with other adhesives.
- 1986-12-28
著者
-
KAWAI Shuichi
Research Institute for Sustainable Humanosphere, Kyoto University
-
SUBIYANTO Bambang
Research Center for Physics
-
Subiyanto Bambang
Research And Development Unit For Biomaterials
-
Kawai Shuichi
Research Institute For Sustainable Humanosphere Kyoto University
-
Kawai Shuichi
Lab. Of Structural Function Div. Of Wood Material Science Wood Research Institute Kyoto University
-
Sasaki Hikaru
Research Section Of Composite Wood Wood Research Institute Kyoto University
-
TAKINO Shinjiro
Research Institute for Sustainable Humanosphere, Kyoto University
-
Takino S
Kyoto Univ. Kyoto
-
Takino Shinjiro
Research Institute For Sustainable Humanosphere Kyoto University
関連論文
- Oxidation of Methoxylated Benzyl Alcohols by Laccase of Coriolus versicolor in the Presence of Syringaldehyde
- De Novo Synthesis of Veratryl Alcohol by Coriolus versicolor
- Aromatic Ring Cleavage of Various β-O-4 Lignin Model Dimers by Phanerochaete chrysosporium
- Elastic moduli and stiffness optimization in four-point bending of wood-based sandwich panel for use as structural insulated walls and floors
- Formation of the density profile and its effects on the properties of fiberboard
- Effects of mat moisture content and press closing spees on the formation of denstiy profile and properties of particleboard
- Fire protection of a laminated veneer lumber joint by wood carbon phenolic spheres sheeting
- Evalluation of fire-retardant properties of edge-jointed lumber from tropical fast-growing woods using cone calorimetry and a standard fire test
- Fire-resistant performance of a laminated venner lumber joint with metal plate connectors protected with graphite phenolic sphere sheeting
- Properties of Particleboard from Lesser-used Species I. : Albizia falcata Backer
- Improvement of fire retardancy of plywood by incorporating boron or phosphate compounds in the glue
- Design and pilot production of a "spiral-winder" for the manufacture of cylindrical laminated venner lumber
- Anisotropic thermal properties of molded carbon phenolic spheres
- Continuous Manufacturing of Cylindrical-LVL by using "Spiral-winding Method"
- Durability of isocyanate resin adhesives for wood V : changes of color and chemical structure in photodegradation
- Evaluation of the fire endurance of mechanically graded timber in bending
- Effects of silane coupling agent level and extraction treatment on the properties of UF-bonded reed and wheat straw particleboards
- Development of high-performance UF-bonded reed and wheat straw medium-density fiberboard
- Sandwich panel of veneer-overlaid low-density fiberboard
- Manufacture and properties of ultra-low-density fiberboard
- Ultra-low Density Fiberboard and Sandwich Panel
- Production and Properties of Composite Fiberboard
- Rheological Properties of Laminated Veneers During Hot-Pressing
- Manufacture and Mechanical Properties of Cylindrical Laminated Veneer Lumber
- Water removal of wet veneer by roller pressing
- The critical stress in various stress levels of bending member on fire exposure for mechanical graded lumber
- In-plane shear properties of the wood-based sandwich panel as a small shear wall evaluated by the shear test method using tie-rods
- Liquid Impregnation in Wood Using a Roller-press In-liquid
- Improvement mechanism of bondability in UF-bonded reed and wheat straw boards by silane coupling agent and extraction treatments
- Upgrading of urea formaldehyde-bonded reed and wheat straw particleboards using silane coupling agents
- Physical Properties of Low-density Particleboard
- Strength, decay and termite resistance of oriented kenaf fiberboards
- Development of wooden portal frame structures with improved columns
- Manufacture of oriented board using mild steam treatment of plant fiber bundles
- Effects of alkali, mild steam, and chitosan treatments on the properties of pineapple, ramie, and sansevieria fiber bundles
- Characterization of the morphological, physical, and mechanical properties of seven nonwood plant fiber bundles
- Manufacture and properties of binderless particleboard from bagasse I : effects of raw material type, storage methods, and manufacturing process
- Changes in micropores in dry wood with elapsed time in the environment
- Classified Characters of Wood Quality in the Junvenile Stage of Cultivars of Japanese Cedar
- Development of binderless fiberboard from kenaf core
- Chemical changes in steam-pressed kenaf core binderless particleboard
- Dimensional Stability and Biological Resistance of Particleboard from Acetylated Albizzia Wood Particles
- Development of new natural polymer-based wood adhesives III : effects of glucose addition on properties of chitosan
- Modeling of a cylindrical laminated veneer lumber II: a nonlinear finite element model to improve the quality of the butt joint
- Modeling of a cylindrical laminated veneer lumber I : mechanical properties of hinoki (Chamaecyparis obtusa) and the reliability of a nonlinear finite elements model of a four-point bending test
- Static Tensile Strength of Wood Butt Joints with Metal Plate Connectors : Effects of Plate Geometry and Specific Gravity of Wood
- Curing and degradation processes of cement-bonded particleboard by supercritical CO_2 treatment
- Kinetic analysis of color changes in cellulose during heat treatment
- Effect of moisture content on manufacturing cement-bonded particleboard using supercritical CO_2
- Characterization of wood-based molding bonded with citric acid