Feasibility of Friction Stir Welding for Joining and Microstructure Refinement in a ZK60 Magnesium Alloy
スポンサーリンク
概要
- 論文の詳細を見る
- Japan Institute of Metalsの論文
- 2007-12-01
著者
-
MOTOHASHI Yoshinobu
Research Center for Superplasticity, Ibaraki University
-
GOLOBORODKO Alexandre
Department of Mechanical Engineering and Intelligent Systems, The University of Electro-Communicatio
-
Mironov Sergey
Research Center For Superplasticity Faculty Of Engineering Ibaraki University
-
Motohashi Yoshinobu
Research Center For Superplasticity Faculty Of Engineering Ibaraki University
-
Goloborodko Alexandre
Department Of Mechanical Engineering And Intelligent System The University Of Electro-communications
-
Ito T
Research Center For Superplasticity Faculty Of Engineering Ibaraki University
-
Kaibyshev Rastum
Institute For Metals Superplasticity Problems Russian Academy Of Sciences
-
Motohashi Y
Research Center For Superplasticity Faculty Of Engineering Ibaraki University
-
ITO Tsutomu
Research Center for Superplasticity, Faculty of Engineering, Ibaraki University
-
FUNAMI Kunio
Department of Machinery Engineering, Chiba Institute of Technology
-
Funami Kunio
Department Of Machinery Engineering Chiba Institute Of Technology
-
Ito Tsutomu
Research Center For Superplasticity Faculty Of Engineering Ibaraki University
関連論文
- Influence of Flat Cavity Formation on Stress vs. Strain and Strain-Rate Relations of Superplastic Deformation in 3Y-TZP
- Grain Refinement in As-Cast 7475 Aluminum Alloy under Hot Equal-Channel Angular Pressing
- Development of Fine-Grained Structure Caused by Friction Stir Welding Process of a ZK60A Magnesium Alloy
- Structural Response of a ZK60 Magnesium Alloy Subjected to Friction Stir Welding(Synergy by Microstructuring)
- Feasibility of Friction Stir Welding for Joining and Microstructure Refinement in a ZK60 Magnesium Alloy
- Development of Die Press-fitted with Die Holder Made of Al Alloy for Compacting Metal Powders
- Evaluation of Compressibility and Ejection Force Using a Tapered Die : Effects of Different Types of Die Wall on Compacted Metal Powders II
- Effects of Different Types of Die Wall on Compacted Metal Powders
- Comparison among SANS Technique and Conventional Methods for Cavity Characterization in Superplastically Deformed Ceramic
- Friction Stir Welding of a Commercial 7075-T6 Aluminum Alloy : Grain Refinement, Thermal Stability and Tensile Properties
- Flat Cavities formed in TZP caused by Superplastic Deformations at High Strain-Rates and Their Effect on Elongation
- Superplastic Response of an Advanced Al-Li-Mg-Cu-Sc Alloy Subjected to Intense Plastic Deformation
- Superplastic Behavior in Al-Li-Mg-Cu-Sc Alloy Sheet
- Effect of Superplastic Deformation on Thermal Expansion Behavior of Tetragonal Zirconia Polycrystals
- Characterization of Cavities in Superplastically Deformed Tetragonal Zirconia Polycrystals by Means of Small Angle Neutron Scattering
- High Strain Rate Superplasticity in an Al-Li-Mg Alloy Subjected to Equal-Channel Angular Extrusion
- Thermal Conductivity of Superplastically Deformed 3Y-TZP
- Development of Shrinkage-Fit Die Coated with Film Possessing Low Friction Coefficient for Compacting Metal Powders
- Effect of Heat Treatment on TEM Microstructures of Zirconium Carbide Coating Layer in Fuel Particle for Advanced High Temperature Gas Cooled Reactor
- Electronic Specific Heat of La_Sr_xCuO_4 : Pseudogap Formation and Reduction of the Superconducting Condensation Energy(Condensed Matter : Electronic Structure, Electrical, Magnetic and Optical Properties)
- Effect of Hydrogenation Treatment on Grain Refinement of Reaction Sintered Ti-6Al-4V Alloy Composites
- Low Temperature Superplasticity and Its Deformation Mechanism in Grain Refinement of AI-Mg Alloy by Multi-Axial Alternative Forging
- 619 Fabrication Process and Mechanical Properties of Fine Grained Aluminum Alloy by Multi-axial Alternative Forging
- The Role of Grain Boundary Sliding in Microstructural Evolution during Superplastic Deformation of a 7055 Aluminum Alloy
- Effects of Neutron Irradiation on Some Superplastic Characteristics of Tetragonal Zirconia Polycrystals Containing 3mol% Yttria
- Effects of Superplastic Deformation on Dynamic Hardness and Young's Modulus of 3Y-TZP(Mechanical Behavior of Materials 2)