Microstructural change by friction stir processing in Zr-Al-Cu-Ni bulk metallic glass (Special issue on bulk metallic glasses: selected papers from the fifth international conference on bulk metallic glasses (BMGV))
スポンサーリンク
概要
著者
-
KOBATA Junpei
Department of Materials Science, Graduate school of Engineering, Osaka Prefecture University
-
Takigawa Yorinobu
Department Of Materials Science Graduate School Of Engineering Osaka Prefecture University
-
Kobata Junpei
Department Of Materials Science Graduate School Of Engineering Osaka Prefecture University
関連論文
- Effect of Tool Materials on Dynamic Friction Characteristics and Microstructural Evolution at Elevated Temperature in Extruded AZ31 Magnesium Alloy
- High-Temperature Plastic Flow in Pre-Annealed Zr-Al-Ni-Cu Bulk Metallic Glass in a Supercooled Liquid Region
- Suppression of Macroscopic Defects through the Control of Friction between Workpiece and Dies in a Forged Magnesium Alloy Part with Ribs
- Effect of Small Addition of Zinc on Creep Behavior of Tin
- Effect of Pre-Introduced Shear Bands Direction on Deformation Behavior in Zr_Al_Ni_5Cu_ Bulk Metallic Glass
- Effect of Initial Grain Size on Dynamically Recrystallized Grain Size in AZ31 Magnesium Alloy
- Optimization of Rolling Conditions in Mg-Al-Ca Alloy Containing Insoluble Second Phase Particles
- Softening by Coarsening of Ni-Al B_2 Phase Particles in Fe-Cr-Ni-Al-Zr Alloy
- Effects of Size and Volume Fraction of Precipitated Crystalline Phase Induced by Friction Stir Processing on Hardness in Zr-Al-Ni-Cu Bulk Metallic Glass
- Investigation on Dynamic Friction Properties of Extruded AZ31 Magnesium Alloy Using by Ring Upsetting Method
- High Cycle Fatigue Property of Extruded Non-Combustible Mg Alloy AMCa602
- High Cycle Fatigue Property and Micro Crack Propagation Behavior in Extruded AZ31 Magnesium Alloys
- Environmentally Friendly Composite Film of Anodizing and Electrodeposition Coating Having a High Corrosion Resistance on Magnesium Alloy AZ91D
- High Corrosion and Weather Resistant Anionic Resin Coating for 2014 T6 Aluminum Alloys Which Maintains Mirror Luster
- Optimization of Environmentally Friendly Anodic Oxide Film for Magnesium Alloys
- Elastic Constants of AlLi from First Principles
- High-Strengthening of Mg-5.5mass%Y-4.3mass%Zn Cast Alloy by Friction Stir Processing
- Effect of Microstructural Change on High-Temperature Deformation in Pre-Annealed Zr_Al_Ni_Cu_ Bulk Metallic Glass
- Novel Electroforming Process for Bulk Nanocrystalline Ni-W Alloys with Minimizing W-Concentration Gradient and Fluctuation
- Application of Electroforming Process to Bulk Amorphous Ni-W Alloy
- Ni-W Amorphous/Nanocrystalline Duplex Composite Produced by Electrodeposition
- Influence of Bath Composition on Tensile Ductility in Electrodeposited Bulk Nanocrystalline Nickel
- Microstructural change by friction stir processing in Zr-Al-Cu-Ni bulk metallic glass (Special issue on bulk metallic glasses: selected papers from the fifth international conference on bulk metallic glasses (BMGV))
- Effect of Titania Doping on Phase Stability of Zirconia Bioceramics in Hot Water
- Clarification of the Necessary Value of Surface Roughness for Developing Luster on an AZ31 Magnesium Alloy Surface with or without Acid Aqueous Solution Treatment
- Addition of an Aminic Antioxidant to a Hindered Ester-Based Heat Resisting Oil to Improve Lubrication for Press Forming of Magnesium Alloy Sheets
- Tribological Properties of Hybrid Process DLC Coating against Magnesium Alloy
- Optimization of Die Material and Its Surface Coating for Press Forming Magnesium Alloy
- Critical Assessments of Tensile Ductility in Superplastic TZP and TiO_2-doped TZP
- Effect of Small Amount of Insoluble Dopant on Tetragonal to Monoclinic Phase Transformation in Tetragonal Zirconia Polycrystal
- Experimental Investigation of Cavitation Behavior in AZ61 Magnesium Alloy
- Dynamic Friction Properties and Microstructural Evolution in AZ31 Magnesium Alloy at Elevated Temperature during Ring Compression Test