Surface Modification of Stainless Steel by Electrical Discharge Machining.
スポンサーリンク
概要
- 論文の詳細を見る
A commercial SUS 304 stainless steel was machined by EDM with a sialon electrode. The machined surface changed from the machining to the surface modification layer on the some proper machining conditions. The effect of the following factors to form the surface layer was investigated: Electrode polarity, work atmosphere and the working condition of the peak current, pulse duration and duty factor. Under the suitable machining conditions, the EDMed surface was covered with the alloyed layer, which consisted of the electrode and work piece components. The surface modified layer improved the corrosion and wear resistance.
- The Iron and Steel Institute of Japanの論文
著者
-
Kojima Yo
Department Of Mechanical Engineering Nagaoka University Of Technology
-
Fukuzawa Yasushi
Department Of Mechanical Engineering Nagaoka University Of Technology
-
Sekiguchi Eiichi
Hitachi Research Laboratory, Hitachi, Ltd.
-
Mohori Naotake
Department of Mechanical Engineering, Toyota Institute of Technology
関連論文
- Improvement of Wear Resistance of Magnesium by Laser-Alloying with Silicon
- Fabrication of Porous Magnesium Alloys by Pulse Electric Current Sintering Process Using Machined Chips
- Improvement of Protium Absorption/Desorption Characteristics of Mg-x mass% LaNi_5 (x=50, 70) Composites by Interface-control
- Protium Absorption/Desorption Characteristics of Mg_2Ni/LaNi_5 Composite
- Development of New Die-castable Mg-Zn-Al-Ca-RE Alloys for High Temperature Applications
- Mechanical Properties of Newly Developed Age Hardenable Mg-3.2mol% Gd-0.5mol%Zn Casting Alloy
- Improvement of Mechanical Characteristics in Severely Plastic deformed Mg Alloys
- Microstructures and Tensile Properties of ECAE-Processed and Forged AZ31 Magnesium Alloy
- Effect of Microstructural Factors on Tensile Properties of an ECAE-Processed AZ31 Magnesium Alloy
- Low Temperature Superplasticity of ECAE Processed Mg-10%Li-1%Zn Alloy
- Mechanical Properties of Mg-Y-Zn Alloy Processed by Equal-Channel-Angular Extrusion
- Effects of Structural Orientation on EDM Properties of Sapphire
- Micro Hole Electrical Discharge Machining on Insulating Ceramics with Pipe Electrode
- B22 Deformation Analysis of Polycarbonate Sheet with Flexible Underlay During Wedge Cutting Process(Advanced machining technology)
- An Investigation of the Structure and Corrosion Resistance of Permanganate Conversion Coatings on AZ91D Magnesium Alloy
- 513 Cutting characteristic of a unique double structure cutter in relation with applied loads
- 319 Effect of Tip Thickness on Cutting Workability of Trapezoidal Bevel Blade Indented to Aluminum Sheet
- Cutting Mechanism and Load Characteristic of Trapezoidal Center Bevel Cutter Indented on Aluminum Sheet(Advanced Manufacturing Technology)
- Improving the Wear Resistance of a Magnesium Alloy by Laser Melt Injection
- Microstructure and Protium Absorbing/Desorbing Characteristics of Mg_2Ni-Mn Alloys
- Tensile Characteristics of Connecting Portions of Paperboard Subjected to Indentation of Nicked Center Bevel Blade
- Role of inflammatory cytokines in liver surgery and therapeutic trials for controlling surgical stress by protease inhibitor and Bcl-xL gene transfer to the hepatocyte
- Mechanical Characteristics of Center Bevelled Double Structure Blade
- Effects of the Edm Combined Ultrasonic Vibration on the Machining Properties of Si_3N_4
- Machining of hard materials by the EDM combined ultrasonic vibration method (第199回電気加工研究会)
- Improvement of Workability and Mechanical Properties of Wrought Magnesium Alloys by Utilizing Dynamic Phenomena
- Creep Properties of Mg-Gd-Y-Zr Alloys
- Aging Characteristics and High Temperature Tensile Properties of Mg-Gd-Y-Zr Alloys
- Surface Modification of Stainless Steel by Electrical Discharge Machining.
- Effect of Hardness Combination on Contact Deformation of Center Bevel Blade with Counter Plate Subjected to a Pushing Load
- Finite Element Analysis of Cutting Deformation of Stacked Polycarbonate Sheets Subjected to Two-Line Wedge Indentation