C233 Comparison of ultra-fast microwave sintering and conventional thermal sintering in manufacturing of anode support solid oxide fuel cell
スポンサーリンク
概要
- 論文の詳細を見る
Microwave sintering with selective susceptor and spacer has been proved to be an effective and facile method in the manufacturing of anode support solid oxide fuel cell (1). Two anode support SOFCs were fabricated by using microwave sintering and thermal sintering techniques, separately. The performances of the two cells were measured and compared in a temperature range of 700℃ to 800℃. The microstructures of the two cells after the measurements were compared qualitatively based on SEM images. FIB-SEM technique was used to reconstruct the 3-D microstructure of both anode and cathode. The quantitative comparison of 3-D reconstructions shows the advantages of using microwave in both anode and cathode sintering processes.
- 一般社団法人日本機械学会の論文
- 2010-10-29
著者
-
Kasagi Nobuhide
Department Of Mechanical Engineering The University Of Tokyo
-
Jiao Zhenjun
Institute of Industrial Science, the University of Tokyo
-
Shikazono Naoki
Institute of Industrial Science, the University of Tokyo
-
Shikazono Naoki
Institute Of Industrial Science The University Of Tokyo
-
Jiao Zhenjun
Institute Of Industrial Science The University Of Tokyo
関連論文
- Modelling the Constitutive Relations for the Reynolds Stress
- Road Map of Micro-Engineering and Nano-Engineering from Manufacturing and Mechanical Engineering Viewpoints(Micro Mechanical Engineering)
- B22-035 PARTICLE TRACKING VELOCIMETRY MEASUREMENT OF CHAOTIC MIXING IN A MICRO MIXER
- Cycle Analysis of Micro Gas Turbine-Molten Carbonate Fuel Cell Hybrid System(Experimental Mechanics in Heat and Fluid Flow)
- Phase-Field simulation of small capillary-number two-phase flow in a microtube
- A Lamination Micro Mixer for μ-Immunomagnetic Cell Sorter(Bioengineering)
- TED-AJ03-550 TURBULENT HEAT TRANSFER IN CHANNEL FLOW WITH NON-ORTHOGONAL SYSTEM ROTATION
- Adjoint Analysis of Heat and Fluid Flow Toward Optimal Shape Design of Recuperators
- Mechanism of Heat Transfer Enhancement in Recuperators with Oblique Wavy Walls
- A New Approach to the Improvement of k-ε Turbulence Model for Wall-Bounded Shear Flows
- Toward Smart Control of Turbulent Jet Mixing and Combustion(Jets, Wakes and Separated Flows)
- Development of Micro Catalytic Combustor with Pt/Al_2O_3 Thin Films(Micro Mechanical Engineering)
- B13-119 Development of Micro Catalytic Combustor with Pt/Al_2O_3 Thin Films
- F307 CONTROL OF WALL SHEAR TURBULENCE WITH ARRAYED MICRO SENSOR/ACTUATOR UNITS(Near-wall turbulence and its control)
- TOWARD SMART CONTROL OF TURBULENT JET MIXING AND COMBUSTION(Keynote Lecture)
- Direct Numerical Simulation of Turbulent Heat Transport at High Prandtl Numbers
- Numerical Prediction of Turbulent Pipe Flow Heat Transfe for Various Prandtl Number Fluids with the Improved k-ε Turbulence Model
- TED-AJ03-231 LARGE EDDY SIMULATION OF MASS TRANSFER ACROSS AN AIR-WATER INTERFACE AT HIGH SCHMIDT NUMBERS
- Study on Micro-Grooved Plate Evaporator
- Heat Transfer and Friction Characteristics in Turbulent Rhombic Duct Flows
- F303 SYNTHESIZED MIXING PROCESS IN AN ACTIVELY-CONTROLLED CONFINED COAXIAL JET(Control of turbulent mixing process)
- Active Control of Wall Turbulence with Wall Deformation
- C233 Comparison of ultra-fast microwave sintering and conventional thermal sintering in manufacturing of anode support solid oxide fuel cell
- Performance Assessment and Improvement of a Spilt-and-Recombine Micromixer for Immunomagnetic Cell Sorting