GSD-02 LOAD BEARING CAPACITY OF SURFACE-ROLLED HIGH DENSITY SINTERED METAL GEARS(GEAR STRENGTH AND DURABILITY, INCLUDING GEAR MATERIALS AND HEAT TREATMENT TECHNIQUES)
スポンサーリンク
概要
- 論文の詳細を見る
This paper describes a study on the load bearing capacity of newly developed high density sintered metal gears with surface-densification. High density sintered metal gears were hobbed, and then surface-rolled. These gears were case-carburized after surface-rolling. The effect of surface-rolling on the surface property was examined by measuring porosities and hardness near surfaces of rolled gears. Running tests for these gears were performed. A failure mode and load bearing capacity of high density sintered metal gears and the effects of surface-rolling on the load bearing capacity of sintered metal gears were determined, and the results were compared with those of carburized wrought steel gears and conventional sintered metal gears. The experimental results show that the load bearing capacity of a newly developed high density sintered metal gear with surface-densification is higher than that of a carburized wrought steel gear.
- 2009-05-13
著者
-
Koide Takao
Department Of Mechanical And Aerospace Engineering Graduate School Of Eng. Tottori University
-
Takemasu Teruie
Department Of Mechanical And System Design Tokyo University Of Science
-
Takemasu Teruie
Department Of Intelligent Machinery And Systems Kyushu University
-
Miyachika Kouitsu
Department Of Mechanical And Aerospace Engineering Graduate School Of Eng. Tottori University
-
ISHIZUKA Ichiro
Department of Mechanical and Aerospace Engineering, Graduate School of Eng., Tottori University
-
FUKAI Yasuhiro
Department of Mechanical and Aerospace Engineering, Graduate School of Eng., Tottori University
-
Fukai Yasuhiro
Department Of Mechanical And Aerospace Engineering Graduate School Of Eng. Tottori University
-
Ishizuka Ichiro
Department Of Mechanical And Aerospace Engineering Graduate School Of Eng. Tottori University
関連論文
- Efficacy of preoperative donation of autologous blood in patients undergoing radical retropubic prostatectomy
- GSD-07 EFFECTS OF CARBURIZED PART, CASE DEPTH AND HELIX ANGLE ON BENDING FATIGUE STRENGTH OF CASE-CARBURIZED HELICAL GEARS(GEAR STRENGTH AND DURABILITY, INCLUDING GEAR MATERIALS AND HEAT TREATMENT TECHNIQUES)
- Crowning Process of P/M Gears for Automotive Transmissions by Finish Rolling Using Screw-Shaped Tool
- GM-18 CONSOLIDATION OF SURFACE LAYER OF P/M GEARS BY FINISH ROLLING WITH SCREW-SHAPED TOOL(GEAR MANUFACTURING)
- Equivalent Misalignment of Gears Due to Deformation of Shafts, Bearings and Gears : Model Proposal and Development of Calculation Program
- GSD-02 LOAD BEARING CAPACITY OF SURFACE-ROLLED HIGH DENSITY SINTERED METAL GEARS(GEAR STRENGTH AND DURABILITY, INCLUDING GEAR MATERIALS AND HEAT TREATMENT TECHNIQUES)
- GSD-27 RESIDUAL STRESSES AND HARDENED LAYERS OF GEARS DUE TO DUAL FREQUENCY INDUCTION HARDENING(GEAR STRENGTH AND DURABILITY)
- Development of Thread Rolled Anti-Loosening Bolts Based on the Double Thread Mechanism and a Performance Evaluation(Recent Advances in Materials and Processing (I))
- PG-03 A STUDY ON LOAD CARRYING CHARACTERISTICS OF PLASTIC CROSSED HELICAL GEAR(PLASTIC GEAR TECHNOLOGY)
- GSD-24 COMPARISON BETWEEN SURFACE LOAD BEARING CAPACITIES OF WN AND INVOLUTE GEARS(GEAR STRENGTH AND DURABILITY)
- GM-05 SURFACE DENSIFICATION CHARACTERISTICS OF CHROMIUM ALLOYED SINTERED STEEL ROLLERS AND GEARS BY FINISH ROLLING(MANUFACTURING OF GEARS)
- Properties of Densification by Surface Rolling and Load Bearing Capacity of 1.5Cr-0.2Mo High Density Sintered Steel Rollers and Gears