W03I Development of stress memory patch(International Workshop on "New Frontiers of Smart Materials and Structural Systems")
スポンサーリンク
概要
- 論文の詳細を見る
A new sensing method called "smart stress memory patch", which could estimate the maximum stress, the stress amplitude and the fatigue cyclic number simultaneously using Kaiser effect of Acoustic Emission (AE) and crack length of this patch, was developed. In this study, the crack growth characteristic of this patch was evaluated. Pure copper was used for this patch because its good corrosion resistance, stable crack propagation and so on. Two kinds of samples which were rolled and electrodeposited copper were prepared to investigate the effect of microstructure on crack growth behavior. Fatigue test was performed under constant stress amplitude to evaluate the crack growth behavior using the relationship between stress intensity factor range and crack propagation rate. The scattering in fatigue crack growth was also investigated to obtain the relationship between crack length and the fatigue cyclic number including two-sided 95% confidence interval. The effect of thickness and grain size on the scattering was discussed. Finally, good crack growth behavior was obtained and the fatigue cyclic number could be estimated by this patch.
- 一般社団法人日本機械学会の論文
- 2006-11-25
著者
-
Enoki Manabu
Department Of Engineering The University Of Tokyo
-
Nambu Shoichi
Department Of Engineering The University Of Tokyo
-
Nambu Shoichi
Department Of Materials Engineering The University Of Tokyo
関連論文
- Fatigue Process Evaluation of Ultrasonic Fatigue Testing in High Strength Steel Analyzed by Acoustic Emission and Non-Linear Ultrasonic
- SCC Monitoring of Chloride Droplets on Thin SUS304 Plate Specimens by Analysis of Continuous Recorded AE Waveform
- Acquisition and Analysis of Continuous Acoustic Emission Waveform for Classification of Damage Sources in Ceramic Fiber Mat
- Evaluation of Thermal Deformation Process of Nickel Based Active Composites by Laser AE Technique
- Crack Monitoring during Plasma Spraying of Ceramic Coatings by Non-Contact Acoustic Emission Method
- Deformation and Anelastic Recovery of Pure Magnesium and AZ31B Alloy Investigated by AE
- Recovery Behaviour of Pure Magnesium in Cyclic Compression-Quick Unloading-Recovery Process at Room Temperature Investigated by AE
- Evaluation of the Twinning Behavior of Polycrystalline Magnesium at Room Temperature by Acoustic Emission
- Classfication of Microfracture Process Type in Glass Matrix Composites by Quantitative Acoustic Emission Method
- Evaluation of Microfracture Mode in Ceramic Coating during Thermal Cycle Test using Laser AE Technique
- Reactive Transient Liquid Phase Bonding between AZ31 Magnesium Alloy and Low Carbon Steel
- Monitoring of Acoustic Emission Activity of Smart Stress Memory Patch to Estimate Maximum Fatigue Stress for Structural Health Monitoring
- Evaluation of Fatigue Properties of Steel Bar by Smart Stress-memory Patch
- Scattering in Fatigue Crack Growth of Thin Pure Copper Sheet for Smart Stress Memory Patch
- Smart Stress-Memory Patch for Fatigue Damage of Structure
- W03I Development of stress memory patch(International Workshop on "New Frontiers of Smart Materials and Structural Systems")
- Fatigue Crack Length Measurement of Sputtered Metal Film for RFID-based Smart Stress Memory Patch
- Detection of AE Events due to Cracks in TBC during Spraying Process
- Strain-Controlled Fatigue Behavior in Thin Pure Copper Sheet for Smart Stress-Memory Patch
- Ferrite Formation Behaviors from B1 Compounds in Steels
- In-Situ Observation and Acoustic Emission Analysis for Corrosion Pitting of MgCl_2 Droplet in SUS304 Stainless Steel
- Finite Element Analysis of Tensile Fatigue Behavior of Coronary Stent
- Effects of Plating Conditions on Electroless Ni-Co-P Coating Prepared from Lactate-Citrate-Ammonia Solution