High Accuracy V-Bending Process Control with an On-Line Database and Modified Fuzzy Models
スポンサーリンク
概要
- 論文の詳細を見る
In this study, a high precision V-bending process control system incorporating an database and modified fuzzy model was developed. Information including the punch force-stroke curve measured in the bending process was stored in the database and applied directly to the process control. In the control system, a new evaluation method, which is called the vectorial evaluation method, was proposed to check irregularities of information in the experimental database, and two modified fuzzy models were developed to compensate defects in the experimental database. Simulation of the control system using the experimental results verified that the proposed control system significantly improves the accuracy and reliability of the process.
- 一般社団法人日本機械学会の論文
- 1997-03-15
著者
-
YANG Ming
Department of Pathology, Tohoku University Hospital
-
Manabe Ken-ichi
Department Of Mechanical Engineering Tokyo Metropolitan University
-
NISHIMURA Hisashi
Department of Mechanical Eengineering, Tokyo Metropolitan University
-
Kojima Naoki
Department Of Mechanical Engineering Tokyo Metropolitan University
-
Nishimura Hisashi
Department Of Applied Science Faculty Of Engineering Kyushu University
-
Yang Ming
Department Of Mechanical Engineering Tokyo Metropolitan University
-
Manabe Ken-ichi
Department Of Mechanical Eengineering Tokyo Metropolitan University
関連論文
- Invasive micropapillary carcinoma of the breast : Clinicopathological and immunohistochemical study
- Microinvasive ductal carcinoma (T1mic) of the breast. The clinicopathological profile and immunohistochemical features of 28 cases
- Fabrication of Superplastic Microtubes Using Dieless Drawing Process
- Crystallographic Orientation Observation and Mechanical Properties Evaluation of Fine-Grained Pure Aluminum
- Experiment and FEM Simulation on Strain Rate Control in the Superplastic Bulge Forming of a Ti-Alloy Tube
- Finite Element Simulation with Coupled Thermo-Mechanical Analysis of Superplastic Dieless Tube Drawing Considering Strain Rate Sensitivity
- チタン合金パイプの超塑性変形過程に対するコンピュータシニュレーション
- High Accuracy V-Bending Process Control with an On-Line Database and Modified Fuzzy Models
- Superplastic Forming of AZ31 Magnesium Alloy Sheet into a Rectangular Pan
- Correlation between performance on the Continuous Performance Test and economic costs in patients with schizophrenia
- Two case studies of hypothermia induced by an increased dosage of zotepine in a combination therapy
- Superplastic Characteristics of Ti-Alloy and Al-Alloy Sheets by Multi-Dome Forming Test
- Drag Reduction Effect of BSA Monodispersed Solution in Microtube Flow
- Geodetically observed surface displacements of the 1999 Chi-Chi, Taiwan, earthquake
- Tribological Behavior and Surface Characteristics of Metal Microtube in Flaring Test
- Thermoforming of Textile Composite Pipe Fittings
- 641 Measurement of variation in Young's modulus after large deformation and simulation of Its influence on Springback Characteristic during bending
- 521 Spring-back analysis based on microscopic measurement of deformation and material properties
- Development and assessment of a medium-range real-time kinematic GPS algorithm using an ionospheric information filter
- An Origin of the Attractive Hubbard Model for High-T_c Superconductivity
- Viscosity of Fermi Particle Systems
- FE Simulation on Blank Holder Control Using Friction Reducing Algorithm in Deep Drawing Process(Recent Advances in Materials and Processing (I))
- Fabrication and Mechanical Characterization of Water-Soluble Resin-Coated Natural Fiber Green Composites
- Effect of Heat Treatment on Microstructure and Mechanical Properties of TRIP Seamless Steel Tube
- Scale Dependence of Adhesion Behavior under Dry Friction in Progressive Micro-Deep Drawing
- Influence of Surface Topographical Interaction between Tool and Material in Micro-Deep Drawing
- Geodetically observed surface displacements of the 1999 Chi-Chi, Taiwan, earthquake