Theoretical Calculation of Propulsive Performances of Stator-Propeller in Uniform Flow by Vortex Lattice Method〔付 討論〕

スポンサーリンク

概要

• 論文の詳細を見る

• By fitting stator vanes behind a screw propeller energy loss of rotational flow in the slip stream of the propeller can be reduced and hence the propeller efficiency can be improved. Then the stator generates thrust to propel a ship. Therefore the screw propeller with the stator behind it acts as one propulsor. We call it stator-propeller in the present paper. So far, experimental methods were used for desiguing stator vanes and for obtaining propulsive performances of the stator-propeller. For experiments we need scale models of the stator-propeller and the ship, and the experimental work is time-consuming and expensive. The aims of the present research are to develop a method for theoretical calculation of propulsive performances of the stator-propeller and to develop a method for design of the stator by theoretical calculation in case that the geometry of the installed screw propeller is known. The vortex lattice method has been employed for the above-mentioned purposes. Kerwin's roll-up model has been applied as the vortex lattice model of the screw propeller. A stator has been represented by one spanwise line vortex along with rectangular vortex rings trailing in downstream. The outside duct has been replaced by a circular vortex ring in the duct and the trailing vortex lattice cylinder in downstream. The developed methods have been applied to two example models of the stator-propeller and the calculated performances have been compared with the results of open water tests. They have shown good agreement. The results of performance calculation show an appreciable improvement in propeller efficiency in open water and additionally the load of the screw propeller has reduced due to the effect of the stator. The twisting angle of the stator vane designed by the developed method for theoretical desigu as for the same two examples has been also in good agreement with that of actual models desigued by the conventional method based on experimental data of rotational angle of flow velocity in the race of the screw propeller. This fact concludes the completion of the theoretical design method of the stator-propeller.

• 社団法人日本船舶海洋工学会の論文

著者

• 池畑 光尚

  Yokohama National University

• Chanda Subrata

  Graduate Student Of Engineering Yokohama National University:india

関連論文

• A Numerical Design Method of Marine Propellers Using Surface Panel Method
• Analysis of Pressure and Stress Distribution on Propeller Blades in Unsteady Flow
• 水槽試験に関するフルード父子の4論文 (その2)
• 流場データを用いた船の推進性能推定法
• 〔抄訳〕水槽試験に関するフルード父子の4論文 (その1)
• スクリュ-プロペラ効率に関する一研究法について(Transaction of the Institution of Naval Architects,Vol.24,1883) (水槽試験に関するフル-ド父子の4論文-2-)
• グレイハウンド号の実験について(Transaction of the Institution of Naval Architects,Vol.15,1874) (水槽試験に関するフル-ド父子の4論文-2-)
• 船体抵抗成分の性質とそれらの相互干渉に関する研究
• Theoretical Analysis of Unsteady Characteristics of Marine Propeller in Ship's Wake
• A Verification of Cavity Model for the Analysis of a Partially Cavitating Two-Dimensional Hydrofoils
• An Investigation of Wake Model and Its Effect on the Hydrodynamic Performance of Propellers by Using a Surface Panel Method〔含 討論〕
• Investigation into Hub Effect of Marine Propeller by Surface Vortex Lattice Method〔含 討論〕
• Application of Dirichlet′s Principle in A New Panel Method for Surface and Tip Flows of Lifting Bodies〔含 討論〕
• A Numerical Method for Designing Three-Dimensional Wing Based on Surface Panel Method〔含 討論〕
• Theoretical Calculation of Propulsive Performances of Stator-Propeller in Uniform Flow by Vortex Lattice Method〔付 討論〕
• Hydroelastic Effects on Propeller Blades in Steady Flow(含 討論)

もっと見る 閉じる

スポンサーリンク