カラーレスセラモメタルクラウンへの試作光重合型モノマーの応用 : マージン修正用ポーセレンの築盛
スポンサーリンク
概要
- 論文の詳細を見る
Collarless ceramo-metal crowns have been widely used because of their superior esthetics at the shoulder as well as the protection of the gingival margin from direct exposure to metal. There are, however, some difficulties in fabricating the crown with satisfactory marginal fit and/or correcting the contour of the loosely fitting porcelain shoulder. In order to overcome such problems in this study, the light-curing process was attempted for forming the porcelain with the experimental monomers. The monomers were composed of 1, 3-butanediol dimethacrylate monomer (BDMA) as a base monomer, glycidil methacrylate monomer (GMA) as a diluent, dl-camphor quinone as a photosensitizer, and N, N-dimethyl-p-toluidine as a reducing agent. Four monomers with different BDMA to GMA ratios were prepared : 1 : 0 0 (referred to as M_<1-0>), 1 : 1 (M_<1-1>), 1 : 1.5 (M_<1-1.5>), and 1 : 2 (M_<1-2>). Their performances were discussed by comparing with the porcelain formed with distilled water followed by firing at 900℃ as a control. The porcelain formed by the light-curing process showed 10 to 15% larger volumetric shrinkage in firing than the control because the porcelain powders could be less incorporated in the mixture with the viscous monomers. The shrinkage not only compensated for the lowered density of the porcelain but also markedly reduced the size of porosities except for the monomer M_<1-0> that produced significantly larger size and number of porosities in the fired porcelain. It was reflected in the compressive strength not smaller than that of the control. When the porcelains formed with the monomers were fired at a temperature lower than 850℃, the shade turned blackish due to the incomplete combustion of the polymers. However, distinguishable color differences could no more be found after firing at 900℃ among the control and the porcelains formed with M_<1-0>, M_<1-1> and M_<1-1.5>. The monomers were applied to form the shoulder porcelain at the margin of the collarless ceramo-metal crown on the plaster die to correct its margin contour. When distilled water was routinely used, a considerable amount of porcelain powders remained on the die shoulder in lifting the crown. With the use of M_<1-0> and M_<1-1>, however, almost all the powders could be withdrawn as a bulk from the die together with the crown, although no improvements were found on the separation from the die with M_<1-1.5> and M_<1-2>. As a result, the margins showed excellent fit to the die shoulder after firing when M_<1-0> and M_<1-1> were used for formation, while larger marginal gaps were observed in the cases of the control and the other two monomers. From the foregoing findings, it was suggested that the light-curing forming of the shoulder porcelain with the experimental monomer M_<1-1> would be an extremely useful technique for improving the workability and marginal fit without adversely affecting the physical and mechanical properties.
- 九州歯科学会の論文
- 1992-02-25
著者
関連論文
- ハイブリッドセラミックスの摩耗に関する研究
- P-2. 口腔インプラント科におけるプロトコールの試作と検討(第 59 回九州歯科学会総会講演抄録)
- P-2 口腔インプラント科におけるプロトコールの試作と検討
- 前装鋳造冠の基本的な支台歯形成
- 増速マイクロ・モーター使用による切削効率に及ぼす切削荷重の影響
- 26. ハイブリッドセラミックスの摩耗に関する研究(第 58 回九州歯科学会総会講演抄録)
- 26 ハイブリッドセラミックスの摩耗に関する研究
- 支台歯形成面に及ぼす増速マイクロ・モーター使用の影響
- 歯科医師の歯冠修復物製作に関する実態調査
- 二重冠方式クラウン・ブリッジの臨床応用
- 歯牙切削時における歯髄腔内の温度変化
- ハイブリッドセラミックスの摩耗に関する研究
- 粉末冶金法の二重冠への応用に関する研究
- チタンと非接触状態にある歯科用合金の溶出挙動
- ポンティック基底面形態の製作に関する実態調査 : 第3報 船底型について
- 粉末冶金を応用する新しい形式の二重冠 : 第2報 表面性状について
- 11. 歯冠修復物製作に対する意識調査(第 55 回九州歯科学会総会講演抄録)
- ポンティック基底面形態の製作に関する実態調査 : 第1報 リッジラップ型について
- 11∿0942 歯冠修復物製作に対する意識調査
- ポンティック下部顎堤形態保持のための多孔性ハイドロキシアパタイト顆粒の抜歯窩応用
- カラーレスセラモメタルクラウンへの試作光重合型モノマーの応用 : マージン修正用ポーセレンの築盛 : 主論文の要旨
- カラーレスセラモメタルクラウンへの試作光重合型モノマーの応用 : マージン修正用ポーセレンの築盛
- 急速加熱型せっこう系埋没材と鋳造体の性状 : 第1報 クラウンの表面性状と適合性
- B-19 急速加熱型せっこう系埋没材の操作変動と鋳造体の適合性
- B-34 急速加熱型せっこう系埋没材の膨張特性とその影響
- 24. 光重合型モノマーのカラーレスポーセレン冠への応用 : 第 1 報 ショルダー部修正用陶材の色調および歯型分離性について(第 50 回九州歯科学会総会講演抄録)
- P∿24 光重合型モノマーのカラーレスポーセレン冠への応用 : 第 1 報 ショルダー部修正用陶材の色調および歯型分離性について