Axisymmetric Stress Analysis and Strength of Bonded Shrink-Fitted Joints of Solid Shaft Subjected to Torsional Loads
スポンサーリンク
概要
- 論文の詳細を見る
Recently, joints that combine a shrink fit with anaerobic adhesives have been used in order to increase joint strength. In this study we deal with the stress analysis and strength evaluation of bonded shrink fitted joints subjected to torsional loads. The stress distributions in the adhesive layer of bonded shrink fitted joints are analyzed by using the axisymmetric theory of elasticity when an external torsion is applied to the upper end of the shaft. The effects of the outer diameter and the stiffness of rings on the interface stress distributions are analyzed by the numerical calculations. Using the interface stress distributions, the joint strength was predicted. In addition, the value of the joint strength was obtained experimentally. It is seen that a rupture in the adhesive is initiated from the upper edge of the interfaces when a torsion is applied to the upper end of the shaft. The numerical results show more conservative values than the experimental results. It is found that the joint strength of bonded shrink-fitted joints is greater than that of shrink-fitted joints.
- 一般社団法人日本機械学会の論文
- 1998-10-15
著者
-
SAWA Toshiyuki
Yamanashi Univ.
-
YONENO Masahiro
Loctite(Japan)
-
Yoneno Masahiro
Loctite(japan)corp.
-
MOTEGI Youichi
Yamanashi University
関連論文
- On characteristics of a bolted joint with a tap bolt
- The Force Ratio of Bolted Joints : The case where clamped parts are flanges
- Effects of the Interface Configurations on the Characteristics of Bolted Joints : the case where clamped parts are two hollow cylinders
- The Strength of Joints Combining Adhesives with Bolts : Case where Adherends are Pipe Flanges of which the Interfaces are Bonded Partially
- Two-Dimensional Stress Analysis of Adhesive Butt Joints Subjected to Tear Loads : Series A : Solid-Mechanics, Strength of Materials
- Three-Dimensional Stress Analysis of Adhesive Butt Joints Subjected to Tensile Loads : The Case Where Adherends are Two Solid Cylinders
- Two-Dimensional Stress Analysis of Adhesive Butt Joints Subjected to External Bending Moments : Series A : Solid-Mechanics, Strength of Materials
- Two-dimensional Stress Analysis of Adhesive Butt Joints Subjected to Tensile Loads
- The Characteristics of Bolted Joints Subjected to External Bending Moments : (Analysis of the Case Where Clamped Parts are Pipe Flanges with Gaskets by Three-Dimensional Theory of Elasticity)
- The Characteristics of Bolted Joints Subjected to External Bending Moments : Analysis of the Case Where Clamped Parts are Pipe Flanges by Three-Dimensional Theory of Elasticity
- Characteristics of Bolted Joints Subjected to External Bending Moments : Analysis of the Case Where Clamped Parts are Circular Flanges by Three-Dimensional Theory of Elasticity
- Effects of the Interface Configurations on the Characteristics of Bolted Joints : The Case Where the Clamped Part is a Cover of Pressure Vessel
- On the Characteristics of Bolted Joints Subjected to Bending Moment : The Casees Where Clamped Parts are T-flanges of Which Interfaces Have Non-contacted Parts
- Axisymmetric Stress Analysis and Strength of Bonded Shrink-Fitted Joints Subjected to Push-Off Forces
- Effects of Plain Washers on the Characteristics of Bolted Joints : Series C : Vibration, Control Engineering, Engineering for Industry
- On the Characteristics of Bolted Joints with Gaskets : Stress Analysis of a Metal Flat Gasket Interposed between Two Hollow Cylinders
- On the Characteristics of Bolted Joints with Gaskets : stress analysis of full face metallic flat gaskets interposed between pipe flanges
- The Characteristics of Bolted Joints with GAskets : Considerations on the Effects by Multiple Bolts Fastening
- On the Characteristics of Bolted Joints with Gaskets : Stress analysis of rectangular metallic flat gaskets interposed between two T-flanges
- Effects of the Interface Configurations on the Characteristics of Bolted Joints : the case where clamped parts are pipe flanges
- Effects of the Interface Configurations on the Characteristics of Bolted Joints : the case where clamped parts are circular flanges
- The Characteristics of Bolted Joints with Gaskets : Stress Analysis of a Metallic Flat Gasket Used for Raised Face in a Cover of Pressure Vessel
- On the Characteristic of a Bolted Joint Subjected to an External Bending Moment : The case where clamped parts are T-flanges
- A Simple Method to Calculate the Force Ratio of Bolted Joints : The case where clamped parts are T-flanges
- Features of Bolted Joints with Tap Bolts : Case where a Clamped Part with a Full Face Metallic Gasket is the Cover of a Pressure Vessel and a Circular Flange
- Contact Stresses in Two Elastic Bodies : Elastic Bodies are Rectangular Plates
- Axisymmetric Stress Analysis and Strength of Bonded Shrink-Fitted Joints of Solid Shaft Subjected to Torsional Loads
- On the Characteristics of Bolted Joints Subjected to External Bending Mometns : The Case Where Clamped Parts are T-flanges with Gaskets or Filler Plates
- On the Characteristics of Bolted Joints with Gaskets : Stress Analysis of Metallic Gaskets with Raised Face Interposed between Pipe Flanges
- The Characteristics of Bolted Joints with Tap Bolts Subjected to External Bending Moments : The Case Where a Clamped Part is T-Flange with a Full Face Metallic Gasket or a Filler Plate : Series C : Vibration Control Engineering Engineering for Industry