TED-AJ03-559 DEVELOPMENT OF MULTI-BED ADSORPTION CHILLER FOR LOW-TEMPERATURE WASTE HEAT RECOVERY
スポンサーリンク
概要
- 論文の詳細を見る
This study aims at improving the performance of thermally activated silica gel-water adsorption refrigeration cycle by introducing multi-bed scheme. In this paper, a 3-bed non-regenerative silica gel-water adsorption chiller design is outlined along with the performance evaluation of the innovative chiller. The 3-bed chiller will be able to work as high efficient single-stage adsorption chiller where driving source temperature is between 60 and 95℃ along with a coolant at 30℃. The 3-bed cycle comprises with three adsorber/desorber heat exchangers, one evaporator and one condenser as can be seen from Fig. A-1. Waste heat or renewable energy sources will power the high temperature desorber. If two beds are in desorption mode, the hot water outlet from the lead desorber will drive the lag desorber before being purged to ambient. This facilitates the maximum utilization of the waste stream. On the contrary, if two adsorber or desorber beds are in adsorption mode, the cooling water outlet from the lead adsorber will cool down the lag adsorber. In this circumstance, two adsorber beds will be connected with the evaporator and will enhance evaporation. The present design allows refrigerant vapor recovery between the high temperature desorber (s) and low temperature adsorber (s) by openning valves 6,7 and 8. This will result in pressure swing in the process and evaporation enhancement. A cycle simulation computer program is developed to analyze the influence of operating temperatures (hot and cooling water temperatures) on cooling capacity and coefficient of performance (COP) of the innovative 3-bed cycle. The cycle simulation calculation indicates that the COP value of the 3-bed chiller is 0.38 with a driving source temperature at 80℃ in combination with coolant inlet and chilled water inlet temperatures at 30℃ and 14℃, respectively. The delivered chilled water temperature is about 6℃ with this operation condition.[figure]
- 一般社団法人日本機械学会の論文
著者
-
Saha Bidyut
Institute Of Advanced Material Study Kyushu University
-
Saha Bidyut
Institute Advanced Material Study Kyushu University
-
Koyama Shigeru
Institute Of Advanced Material Study Kyushu University
-
KUWAHARA Ken
Institute of Advanced Material Study, Kyushu University
-
Kuwahara Ken
Institute Of Advanced Material Study Kyushu University
-
Kuwahara Ken
Institute For Materials Chemistry And Engineering Kyushu University
-
Koyama Shigeru
Institute For Materials Chemistry And Engineering Kyushu University
-
Koyama Shigeru
Institute Advanced Material Study Kyushu University
関連論文
- Characteristics of Evaporation Heat Transfer and Flow Pattern of Pure Refrigerant HFC134a in a Horizontal Capillary Tube
- E209 CHARACTERISTICS OF EVAPORATION HEAT TRANSFER AND FLOW PATTERN OF PURE REFRIGERANT HFC134a IN A HORIZONTAL CAPILLARY TUBE(Evaporation-1)
- TED-AJ03-292 FLOW AND ABSORPTION CHARACTERISTICS OF AMMONIA-WATER MIXTURE IN A SLUG FLOW ABSORBER AT LOW SOLUTION FLOW RATE
- Isothermal Adsorption Measurement for the Development of High Performance Solid Sorption Cooling System
- Multi-Bed Multi-Stage Adsorption Refrigeration Cycle-Reducing Driving Heat Source Temperature
- Local Heat and Mass Transfer in a Counter-current Slug Flow Absorber for Ammonia-water Absorption Heat Pump System (特集 ACRA-2002講演論文選集(1))
- TED-AJ03-559 DEVELOPMENT OF MULTI-BED ADSORPTION CHILLER FOR LOW-TEMPERATURE WASTE HEAT RECOVERY
- Experiments on Single Phase Heat Transfer and Pressure Drop in a Spiral Capillary Tube
- Experimental Study on Flow Boiling Heat Transfer and Pressure Drop Characteristics of HFC134a in a Multi-Port Extruded Tube
- I302 CONDENSATION OF BINARY ZEOTROPIC WORKING FLUID IN A PLATE HEAT EXCHANGER(Condensation and heat exchanger)
- TED-AJ03-200 EXPERIMENTAL STUDY ON VAPOR-LIQUID TWO-PHASE FLOW OF R134A INSIDE SMOOTH AND MICROFIN TUBES : RELATION OF VOID FRACTION AND VAPOR QUALITY AT ADIABATIC CONDITION
- TED-AJ03-311 HEAT TRANSFER AND PRESSURE DROP CHARACTERISTICS OF R134a CONDENSING IN A MULTI-PORT EXTRUDED TUBE
- I303 HEAT TRANSFER CHARACTERISTICS OF PURE REFRIGERANT HFC134a CONDENSING IN A MULTI-PORT EXTRUDED TUBE(Condensation and heat exchanger)
- An Experimental Study of Evaporation Heat Transfer of Refrigerant HCFC22 Inside an Internally Grooved Horizontal Tube
- Condensation of Binary Refrigerant Mixtures in a Horizontal Smooth Tube
- Numerical study on in-tube laminar heat transfer characteristics of CO_2 at supercritical condition
- Experiment on Cooling Heat Transfer of Carbon Dioxide in a Multi-Port Extruded Tube at Supercritical Pressure
- Condensation of A Ternary Zeotropic Refrigerant Mixture in A Horizontal Micro-fin Tube