鉄浴型溶融還元炉における燃焼機構の解析(溶融還元)(<特集>製銑)
スポンサーリンク
概要
- 論文の詳細を見る
A numerical analysis based on the mathematical model has been made on the combustion phenomena in an iron bath type smelting reduction furnace. This model deals with seven components : C, CO, CO_2, O_2, H_2, H_2O, N_2. Gas flow, temperature distribution in smelting reduction furnace were calculated. The change of post combustion ratio by coal species and coal feed rate into smelting reduction furnace was calculated and compared with 5 t scale experiment. The model was also used to calculate material and heat balance when heat loss amount and prereduction degree of ore changed. It was found that the material and heat balance point was determined uniquely by coal species, heat loss amount, and prereduction degree of ore. In this balance point, ore and coal feed rates are determined uniquely, post combustion ratio and heat efficiency are also determined, so coal and oxygen consumption and productivity at this point can be calculated.
- 社団法人日本鉄鋼協会の論文
- 1992-07-01
著者
-
高本 泰
新日本製鉄(株)プロセス技術研究所
-
篠竹 昭彦
新日本製鉄(株)プロセス技術研究所
-
Takamoto Y
Nippon Steel Corp. Chiba Jpn
-
Takamoto Yasushi
Environment & Process Technology Center Nippon Steel Corporation
関連論文
- 122 加圧下での鉄溶融還元挙動について : 加圧精錬法に関する研究 III(新製鉄・溶融還元, 製銑・製鋼共通, 日本鉄鋼協会第 113 回(春季)講演大会)
- 88 羽口部酸化鉄吹込みによる脱 Si 実験(高炉内分布, 高炉低シリコン操業, 羽口吹込み, 製銑, 日本鉄鋼協会第 109 回講演大会)
- 128 鉱石・石炭混合塊成化物の溶融還元(新製錬, 溶融還元, 製銑・製鋼共通, 日本鉄鋼協会第 114 回(秋季)講演大会)
- 121 スラグ中の酸化鉄の溶融還元反応速度(新製鉄・溶融還元, 製銑・製鋼共通, 日本鉄鋼協会第 113 回(春季)講演大会)
- Optimization of Chemical Composition and Microstructure of Iron Ore Sinter for Low-temperature Drip of Molten Iron with High Permeability
- 99 高炉羽口・炉床状況に及ぼす送風温度・湿分の影響 : 広畑 3 高炉試験操業報告その 2(高炉耐火物・高炉操業・微粉炭利用, 製銑, 日本鉄鋼協会 第 105 回(春季)講演大会)
- Blast Furnace Ironmaking System Using Partially Reduced Iron Ore Reduced by an Energy Source with Low Carbon Content
- 54 塊状帯ガス流れの測定(高炉 (1)(羽口吹込・熱風炉), 高炉 (2)(装入物分布・ガス流れ), 製銑, 日本鉄鋼協会第 107 回(春季)講演大会)
- 117 高炉融着帯の溶け落ちレベルの推定技術(高炉操業, 製銑, 日本鉄鋼協会第 104 回(秋季)講演大会)
- 部分還元鉱石を使用する高炉製銑プロセス (製銑特集)
- 名古屋1高炉における還元鉄高配合操業 (還元鉄の高炉使用 -2)
- 高炉操業に与える還元鉄の影響の基礎検討 (還元鉄の高炉使用 -1)
- 循環流動層による粉鉱石の還元(新鉄源・リサイクル)(製銑プロセスの機能強化と新展開)
- 循環流動層による粉鉄鉱石の還元
- 循環流動層による高炉二次灰の脱Zn処理
- 鼓胴型回転流動層による粉鉱の向流還元(製銑)
- 101 高炉シャフト部における鉱石中アルカリ挙動(高炉炉内解析, 製銑, 日本鉄鋼協会第 103 回(秋季)講演大会)
- 鉄浴型溶融還元炉における燃焼機構の解析(溶融還元)(製銑)
- 63 炉頂ガス流速分布および装入面形状の測定に基く塊状帯ガス流れの解析(装入物分布・装入物炉内性状・融着帯・炉下部現象・溶銑中 Si・代替燃料吹込, 製銑, 日本鉄鋼協会 第 102 回(秋季)講演大会)
- 43 鼓胴型回転流動層による粉鉱の向流還元(製銑基礎, 製銑・環境, 日本鉄鋼協会第 94 回(秋季)講演大会)
- 焼結鉱の還元粉化挙動
- 予備還元鉱石使用時の高炉製銑プロセス
- 循環流動層による粉鉄鋼石の還元速度