Relationship between Flow Characteristics and Surface Quality in Inclined Twin Roll Strip Casting

スポンサーリンク

概要

• 論文の詳細を見る

• Good surface quality is essential for the twin roll cast stainless steel strip to be directly cold-rolled. Thus, surface quality of AISI 304 stainless steel is one of the main problems for the twin roll strip casting process to be put into commercial production. The surface defects commonly appeared in the as-cast strip of twin roll process may include longitudinal and transverse cracks or wrinkles as well as unevenness which is mainly caused by gas trapping and surface vibration of meniscus between the two rolls. In this study, a modeling software was applied to simulate the flow behavior of molten pool at quasi-steady state in inclined twin roll casting and to investigate the relationship between flow characteriatics and surface quality of the produced thin strip. The flow characteristics was drawn from the calculated flow patterns and then correlated to the surface quality of thin strips produced in an experimental caster under the same casting condition as the calculations. Through this procedures, several correlations were then found. First, the surface wrinkles appeared on the thin strip when the pool levels were low. The problem was improbed with a higher pool level due to less flow violence nor meniscus fluctuation. Second, the recirculation with a large vortex occurring around the triple intersection point of the roll/melt/air three phases was the main cause for the slag and/or dross trapping. Third, by using a higher roll angle along with an inclined feeding position nearer to the lower roll, a much table flow on the meniscus surface could be obtained.

• 社団法人 日本鉄鋼協会の論文
• 1996-06-15

著者

• Hwang W.

  Department Of Materials Science And Engineering National Cheng Kung University

• Hwang J.

  Department Of Electrical Engineering Korea Advanced Institute Of Science And Technology (kaist)

• Hwang W.

  Department Of Materials Science And Engineering National Cheng-kung University

• LIN H.

  Materials Research Laboratories, ITRI

• JANG J.

  Materials Research Laboratories, ITRI

• HU C.

  Department of Materials Science and Engineering, National Tsing-Hua University

• Hwang J.

  Department Of Materials Science And Engineering National Tsing-hua University

• Hu C.

  Department Of Materials Science And Engineering National Tsing-hua University

• Jang J.

  Materials Research Laboratories Itri

• Lin H.

  Materials Research Laboratories Itri

関連論文

• NaCl濃度を減少した培養液によるウシ体外受精卵の単精子受精率の向上と胚盤胞への発育
• Magnetization of Finite Carbon Nanotubes(Condensed Matter : Electronic Structure, Electrical, Magnetic and Optical Properties)
• Bearing strength of carbon/epoxy composite laminates
• Observation of static strength and fatigue life of repaired graphite/epoxy using a tensile coupon
• 胚作出のための核移植計画から排除されたブタ卵子の単為生殖化による供給(臨床繁殖学)
• Magnetoelectronic Properties of a Single-Layer Graphite(Condensed matter: electronic structure and electrical, magnetic, and optical properties)
• A 0.8-μm CMOS 1.33 to 2-GHz Wide Range Tunable Two-Stage Current Steering L-C Oscillator
• A 0.8-μm CMOS 1.33 to 2-GHz Wide Range Tunable Two-Stage Current Steering L-C Oscillator
• A 0.8-μm CMOS 1.33 to 2-GHz Wide Range Tunable Two-Stage Current Steering L-C Oscillator
• Lung Transplantation Status in Korea
• Relationship between Flow Characteristics and Surface Quality in Inclined Twin Roll Strip Casting
• Multi-phase Flow Simulations in Direct Iron Ore Smelting Reduction Process
• PPS-14基調講演・招待講演より カオス的流動による一軸押出機の混合性能向上
• Successful Treatment of Idiopathic Hypereosinophilic Syndrome with Imatinib Mesylate : A Case Report
• Measurement of strain and axial contraction of an FRP tube under large rotation
• Nitride-Based UV Metal–Insulator–Semiconductor Photodetector with Liquid-Phase-Deposition Oxide
• Lung Transplantation in Patients with Pulmonary Emphysema

もっと見る 閉じる

スポンサーリンク