Prediction of Raceway Shape and Size
スポンサーリンク
概要
- 論文の詳細を見る
Prediction of raceway shape and size has always been a challenging task. Based on the previous finding that raceway boundary is an iso-stress boundary, its shape and size has been predicted using a continuum approach. A relation has also been developed to get the stress at the raceway boundary at different blast velocity. Predicted raceway boundary is compared with the experimental raceway boundary/shape and size along with the comparison of theoretical and experimental pressure distribution. A reasonable agreement between the theoretical and experimental raceway shape and size is found. Extension of the work in real blast furnace case is also discussed.
- 社団法人 日本鉄鋼協会の論文
- 2007-12-15
著者
-
Kitamura Shin-ya
Institute of Multidisciplinary Research for Advanced Materials, Tohoku University
-
Kitamura Shin-ya
Institute Of Multi-disciplinary Research On Advanced Materials Tohoku University
-
GUPTA Govind
Department of Materials Engineering, Indian Institute of Science
-
Kitamura Shin-ya
Inst. Of Multidisciplinary Res. For Advanced Materials Tohoku Univ.
-
SARKAR Sabita
Department of Materials Engineering, Indian Institute of Science
-
Gupta Govind
Department Of Materials Engineering Indian Institute Of Science
-
Sarkar Sabita
Department Of Materials Engineering Indian Institute Of Science
関連論文
- Evaluation of Bubble Eye Area to Improve Gas/Liquid Reaction Rates at Bath Surfaces
- Some Aspects on Grain Refining Additions with Focus on Clogging during Casting
- Analysis on Material and Energy Balances of Ironmaking Systems on Blast Furnace Operations with Metallic Charging, Top Gas Recycling and Natural Gas Injection
- Analysis of Dephosphorization Reaction Using a Simulation Model of Hot Metal Dephosphorization by Multiphase Slag
- Effect of Bottom Bubbling Conditions on Surface Reaction Rate in Oxygen-Water System
- Behavior of Cobalt in Iron- and Steel-making Processes
- Distribution of P_2O_5 between Solid Dicalcium Silicate and Liquid Phases in CaO-SiO_2-Fe_2O_3 System
- Prediction of Raceway Shape and Size
- Mass Transfer of P_2O_5 between Liquid Slag and Solid Solution of 2CaO・SiO_2 and 3CaO・P_2O_5
- Distribution of P_2O_5 between Solid Solution of 2CaO・SiO_2-3CaO・P_2O_5 and Liquid Phase
- Distribution of Cobalt between MgO-Saturated FeO_x-MgO-CaO-SiO_2 Slag and Fe-Cu-Co Molten Alloy
- Influence of Bottom Bubbling Condition on Metal Emulsion Formation in Lead-Salt System
- Degree of Undercooling and Contact Angle of Pure Iron at 1933K on Single-crystal Al_2O_3, MgO, and MgAl_2O_4 under Argon Atmosphere with Controlled Oxygen Partial Pressure
- Evaluation of Bubble Eye Area to Improve Gas/Liquid Reaction Rates at Bath Surfaces
- Behavior of Vanadium and Niobium during Hot Metal Dephosphorization by CaO-SiO_2-Fe_tO Slag
- Influence of Solid CaO and Liquid Slag on Hot Metal Desulfurization
- Mechanism of Change in Chemical Composition of Oxide Inclusions in Fe-Cr Alloys Deoxidized with Mn and Si by Heat Treatment at 1473 K
- Preface to the Special Issue on "Fundamentals and Applications of Non-metallic Inclusions in Solid Steel"
- Influence of Bottom Bubbling Rate on Formation of Metal Emulsion in Al–Cu Alloy and Molten Salt System
- Influence of Bottom Bubbling Rate on Formation of Metal Emulsion in Al-Cu Alloy and Molten Salt System
- Influence of Slag Basicity and Temperature on Fe and Mn Distribution between Liquid Fe–Mn–Ca–O–S Matte and Molten Slag
- Equilibrium Distribution Ratio of Phosphorus between Solid Iron and Magnesiowustite-saturated Al2O3–CaO–FetO–MgO–SiO2 Slag at 1623 K