Iron Aluminide Coating of Structural Steel by Mechanical Alloying Followed by Annealing
スポンサーリンク
概要
- 論文の詳細を見る
Iron aluminide coating of structural steel by mechanical alloying (MA) followed by annealing was examined. As starting materials, stabilized Al powders containing fat, fat-free Al powders and pure Fe powders were used. Stabilized Al-25 at% Fe powder deposited on the steel substrate from the early stage of MA and formed the coating layer. The mixing and the refinement of Al rich and Fe rich phases in the coating layer were promoted by the suppression of cold welding due to the presence of fat in the coating layer, resulting in the formation of coating layer with fine and homogeneous microstructure. In annealing for 7.2 ks after MA, Fe2Al5 was formed at 673 K, Fe2Al5 and FeAl were formed at 873 K and Fe2Al5, FeAl and Fe3Al were formed at1073 K, respectively. Thus, the formation temperature of FeAl was lower than that of the conventional hot dip coating or pack cementation. This is because interdiffusion between the steel substrate and the coating layer is enhanced by the refinement of microstructure of coating layer due to MA. By coupling annealing to MA, it is possible to improve embrittlement of iron aluminide coating layer.
- 2009-07-15
著者
-
Wismogroho Agus
Department Of Nano Structure And Advanced Materials Graduate School Of Science And Engineering Kagos
-
Sueyoshi Hidekazu
Department Of Mechanical Engineering Faculty Of Engineering Kagoshima University
-
Rochman Nurul
Research Center For Physics Indonesian Institute Of Science
-
Rochman Nurul
Research Center For Physics Indonesian Institute Of Sciences Kompleks Puspiptek Serpong
-
IRAWANTO Heru
Research Center for Physics, Indonesian Institute of Sciences, Kompleks PUSPIPTEK Serpong
-
WIDAYATNO Wahyu
Research Center for Physics, Indonesian Institute of Sciences, Kompleks PUSPIPTEK Serpong
-
NOVIANTO Alfian
Research Center for Physics, Indonesian Institute of Sciences, Kompleks PUSPIPTEK Serpong
-
Irawanto Heru
Research Center For Physics Indonesian Institute Of Sciences Kompleks Puspiptek Serpong
-
Novianto Alfian
Research Center For Physics Indonesian Institute Of Sciences Kompleks Puspiptek Serpong
-
Widayatno Wahyu
Research Center For Physics Indonesian Institute Of Sciences Kompleks Puspiptek Serpong
-
Sueyoshi Hidekazu
Department Of Nano Structure And Advanced Materials Graduate School Of Science And Engineering Kagos
関連論文
- Removal of Lead from Copper Alloy Scraps by Compound-Separation Method
- LCA of Manufacturing Lead-Free Copper Alloys
- Effect of Processing Conditions on Gas Nitriding of Austenitic Stainless Steels
- Effect of Preheating in Air on Gas Nitriding of Austenitic Stainless Steels
- Effects of microstructural factors and alloying elements on dezincification of brass
- Removal of lead from scrap brass
- Solid State Bonding of Graphite to S45C Steel
- Processing of a Continuous Ceramic Fiber-Reinforced Iron Alloy
- Processing of a Continuous Ceramic Fiber/Iron Alloy Composite
- Iron Aluminide Coating of Structural Steel by Mechanical Alloying Followed by Annealing
- Effect of Preheating in Air on Gas Nitriding of SUS304 Stainless Steel
- Effect of preforms on the synthesis of micro β-SiC from phenol resin and silicon
- Damping Capacity of Graphite-Dispersed Composite Steel
- Solid State Bonding of Graphite to SUS304 Steel
- Effect of Mechanical Pretreatment on Gas Nitriding Behavior of Austenitic Stainless Steels
- Fe-C System Alloys Prepared by Mechanical Alloying and Powder Metallurgy
- Solid State Bonding of Graphite to Inconel 718
- Solid State Bonding of Graphite to Nickel^
- Effect of Graphitization on Solid State Bonding of Carbon to Nickel
- Effects of Carbon Fiber Orientation and Graphitization on Solid State Bonding of C/C Composite to Nickel
- Effect of Joining Compressive Stress on Solid State Bonding of Graphite to Nickel
- Microwave Heating of Thin Au Film