Numerical and Modeling Analysis of Fluid Flow and Heat Transfer of Liquid Steel in a Tundish with Different Flow Control Devices
スポンサーリンク
概要
- 論文の詳細を見る
Fluid flow and heat transfer of liquid steel in a two-strand tundish of a slab caster were analyzed using water modeling and numerical techniques. Three cases were considered: A bare tundish, a tundish equipped with a pair of weirs and a pair of baffles (arrangement W&B) and a tundish equipped with a turbulence inhibitor and a pair of baffles (arrangement TI&B). The water modeling, under isothermal conditions, indicated the existence of a strong bypass-flow for the bare tundish and the W&B arrangement while the TI&B arrangement reported a longer minimum residence time and higher plug flow characteristics. Numerical results verified the trend mentioned with the water model. The numerical study showed also that cold and hot steel affected considerably the flow patterns of steel due to the existence of buoyancy forces. In the case of a step-input of cold steel, bypass-flow was intensified for the bare tundish and the tundish with a W&B arrangement. When a step input of hot steel is introduced into the system buoyancy forces make the steel to flow preferentially near the free surface. The tundish with a TI&B arrangement showed the best flow characteristics with not splashing and negligible turbulence. This arrangement shows a slower response to thermal disturbs coming from the input making the tundish a less exposed reactor to the temperature changes and the consequent changes in flow patterns usually found in real casting operations.
- 社団法人 日本鉄鋼協会の論文
- 1999-05-15
著者
-
Palafox-ramos J.
Instituto Politecnico Nacional-esiqie (www.ipn.mx) Department Of Metallurgy And Materials Engineerin
-
Morales R.
Department Of Metallurgy And Materials Engineering The National Polytechnic Institute-esiqie
-
Palafox-ramos J.
Department Of Metallurgy And Materials Engineering The National Polytechnic Institute-esiqie
-
LOPEZ-RAMIREZ S.
Department of Metallurgy, Instituto Politecnico Nacional-E. S. I. Q. I. E.
-
ZACHARIAS D.
Department of Metallurgy, Instituto Politecnico Nacional-E. S. I. Q. I. E.
-
Lopez-ramirez S.
Department Of Metallurgy Instituto Politecnico Nacional-e. S. I. Q. I. E.
-
Morales R.
Department Of Metallurgy
-
Morales R.
Department Of Metallurgy Instituto Politecnico Nacional-e. S. I. Q. I. E.
-
Zacharias D.
Department Of Metallurgy Instituto Politecnico Nacional-e. S. I. Q. I. E.
関連論文
- 重篤度が異なる患者から分離されたデングウィルスに対する由来の異なるネッタイシカマ集団の感受性
- A Physical Model for the Two-phase Flow in a Continuous Casting Mold
- A DPIV Study of Liquid Steel Flow in a Wide Thin Slab Caster Using Four Ports Submerged Entry Nozzles
- A Mathematical Model for Reduction Kinetics of Iron Oxide in Electric Furnace Slags by Graphite Injection
- Flow Dynamics in Thin Slab Molds Driven by Sustainable Oscillating Jets from the Feeding SEN
- Numerical and Modeling Analysis of Fluid Flow and Heat Transfer of Liquid Steel in a Tundish with Different Flow Control Devices
- The Slag Foaming Practice in EAF and Its Influence on the Steelmaking Shop Productivity
- Modeling the Effects of a Swirling Flow on Temperature Stratification of Liquid Steel and Flotation of Inclusions in a Tundish
- 255 High Decarburization Rates During the Refining of Fe-Cr-Ni-C Alloys in EAF(STEELMAKING, The 112th ISIJ Meeting)
- Heat Transfer Analysis during Water Spray Cooling of Steel Rods