Effects of Primary Oxide and Oxide-Nitride Particles on the Solidification Structure in a Fe-20 mass%Cr Alloy Deoxidised with Ti and M (M = Zr or Ce)
スポンサーリンク
概要
- 論文の詳細を見る
The ratio of equiaxed grains on a cross section and the size of equiaxed grains in a Fe-20 mass% Cr alloy deoxidised with Ti/M (M = Zr or Ce) were studied as function of nitrogen content and particle characteristics such as size distribution, morphology and composition. Fe-20 mass% Cr alloys were melted at 1600°C, deoxidised, and cooled to 1400°C followed by water quenching. Thereafter, the particles were separated from the matrix using electrolytic extraction using a 10%AA electrolyte and collected on a film-filter surface. The inclusion characteristics were determined using SEM. It was found that the number of particles increases with an increased N content. Furthermore, that the solidification structure was clearly affected by the number of primary oxide and oxide-nitride particles in the Ti/Zr deoxidation experiments. However, a similar effect could not be detected in the Ti/Ce deoxidation experiments.
著者
-
Nakajima Keiji
Department Of Materials Science And Engineering Royal Institute Of Technology (kth)
-
INOUE Ryo
IMRAM, Tohoku University
-
Jonsson Par
Department Of Materials Science And Engineering Royal Institute Of Technology
-
Nakajima Keiji
Department of Materials Science and Engineering, KTH
-
Janis Jesper
Department of Materials Science and Engineering, KTH
-
Karasev Andrey
Department of Materials Science and Engineering, KTH
-
Jonsson Stefan
Department of Materials Science and Engineering, KTH
-
Jönsson Pär
Department of Materials Science and Engineering, KTH
-
JONSSON Par
Department of Materials Science and Engineering
関連論文
- Swinging Motion of Bath Surface Induced by Side Gas Injection
- Physical Modeling of a Sampler Filling for Molten Steel
- Theoretical and Experimental Assessment of the Kinetic Properties of N-isopropyl-p-[^<123>I] iodoamphetamine in the Human Brain
- Intradural-extramedullary Spinal Cavernous Angioma : Case Report
- Influences of Physical Properties of Particle in Discrete Element Method on Descending Phenomena and Stress Distribution in Blast Furnace
- Solidified Structure Control of Metallic Materials by Static High Magnetic Fields
- Prediction of Solidification Paths for Fe-C-Cr Alloys by a Multiphase Segregation Model Coupled to Thermodynamic Equilibrium Calculations
- Application of the Sulphide Capacity Concept on High-basicity Ladle Slags Used in Bearing-Steel Production
- Basiparallel Tomography to Diagnosis of an Extraaxial Mass in the Posterior Fossa
- Preface to the Special Issue on "Cutting Edge of Studies in Inclusions and Precipitates Behavior Related to Microstructure Control"
- Mathematical Comparison of Two VOD Nozzle Jets
- Mathematical Modeling of Scrap Melting in an EAF Using Electromagnetic Stirring
- Effects of Primary Oxide and Oxide-Nitride Particles on the Solidification Structure in a Fe-20 mass%Cr Alloy Deoxidised with Ti and M (M = Zr or Ce)
- Effect of Secondary Nitride Particles on Grain Growth in a Fe-20 mass% Cr Alloy Deoxidised with Ti and Zr
- Influence of Liquid Metal Properties on Water Atomised Iron Powders
- Effect of Secondary Nitride Particles on Grain Growth in a Fe-20 mass% Cr Alloy Deoxidised with Ti and Zr
- Effects of Primary Oxide and Oxide-Nitride Particles on the Solidification Structure in a Fe-20 mass%Cr Alloy Deoxidised with Ti and M (M=Zr or Ce)