Evaluation of Critical Gas Flow Rate for the Entrapment of Slag Using a Water Model.

スポンサーリンク

概要

• 論文の詳細を見る

• Cold model experiments were performed to make clear the critical condition causing the entrapment of slag under bottom gas injection. Entrapment of slag was judged from visual observation. The following empirical correction of the critical liquid velocity on the centerline of the vessel. u<SUB><I>cl, c</I></SUB> was derived.u<SUB><I>cl, c</I></SUB>/<I>V</I>=1.2(ν<SUB><I>s</I></SUB>/ν<SUB><I>m</I></SUB>)<SUP>0.068</SUP>(<I>H<SUB>s</SUB>/D</I>)<SUP>-0.11</SUP> <I>d<SUB>B</SUB>/D<H<SUB>s</SUB>/D<</I>1/2, 0.6<ρ<SUB><I>s</I></SUB>/ρ<SUB><I>m</I></SUB><1, 0.3<ν<SUB><I>s</I></SUB>/ν<SUB><I>m</I></SUB><120, 45 mN/m<σ<SUB><I>ms</I></SUB><63 mN/m u<SUB><I>cl, c</I></SUB>=1.2 <I>u<SUB>r</SUB>P</I><SUP>-0.28</SUP> <I>u</I><SUB>r</SUB>=(<I>gQ<SUB>a, c</SUB>/H<SUB>m</SUB></I>)<SUP>1/3</SUP> <I>P</I>={Q<SUP>2</SUP><SUB>a, c</SUB>/(<I>gH<SUB>m</SUB></I><SUP>5</SUP>)}<SUP>1/5</SUP> <I>V</I>=(σ<SUB><I>ms</I></SUB><I>g</I>/ρ<SUB><I>s</I></SUB>)<SUP>1/4</SUP> where, <I>g</I>: the acceleration due to gravity, <I>Q<SUB>a, c</SUB></I>: the critical gas flow rate for the entrapment of slag, <I>H<SUB>m</SUB></I>: the thickness of metal layer, σ<SUB><I>ms</I></SUB>: the interfacial tension between slag and metal, ρ<SUB><I>s'</I></SUB>, ρ<SUB><I>m</I></SUB>: the densities of slag and metal, ν<SUB><I>s'</I></SUB>, ν<SUB><I>m</I></SUB>: the kinematic viscosities of slag and metal, <I>H<SUB>s</SUB></I>: the thickness of slag layer, <I>D</I>: the bath diameter, <I>d<SUB>B</SUB></I>: the bubble diameter. This correlation could predict the critical gas flow rate <I>Q<SUB>a, c</SUB></I> for previous hot model experiments as well, provided that the flow pattern in the baths were similar to the present case.

• The Iron and Steel Institute of Japanの論文

著者

• IGUCHI Manabu

  Faculty of Engineering, Osaka University

• Morita Zen-ichiro

  Faculty Of Engineering Osaka University

• Iguchi Manabu

  Faculty Engineering Osaka University

• Sumida Yutaka

  Graduate Student, Osaka University

• Okada Ryusuke

  Undergraduate Student, Osaka University

関連論文

• X-ray Fluoroscopic Observation of Bubble Characteristics in a Molten Iron Bath
• デローニー三角分割に基づく新しいPIV相関アルゴリズムの提案
• Transient Powder-Laden Liquid Jet in a Pipe Flow
• The Structure of Turbulence in Pulsatile Pipe Flow Accompanied by Relaminarization
• Velocity Distributions in Laminar Phases for Oscillatory Rectangular Duct Flows with Occurrence of Turbulent Transition
• Time-Dependent Wall Shear Stress in a Duct with Arbitrary Cross-Section
• Laminar-Turbulent Transition and Velocity Profiles of Oscillatory Rectangular Duct Flows
• Flow Pattern and Frictional Losses in Pulsating Pipe Flow : Part 5, Wall Shear Stress and Flow Pattern in a Laminar Flow
• Flow Pattern and Frictional Losses in Pulsating Pipe Flow : Part l, Effect of Pulsating Frequency on the Turbulent Flow Pattern
• A Experimental Study of Velocity Distribution and Inlet Length in the Inlet Region of Laminar Oscillatory Pipe Flow : Series B : Fluid Engineering, Heat Transfer, Combustion, Power, Thermophysical, Properties
• Turbulent Slug and Velocity Field in the Inlet Region for Pulsatile Pipe Flow : Fluids Engineering
• Flow Patterns and Frictional Losses in an Oscillating Pipe Flow
• Transition to Turbulence in a Pulsatile Pipe Flow Part 1,Wave Forms and Distribution of Pulsatile Velocities near Transition Region
• Velocity Distribution and Reattachment Length in an Oscillatory Pipe Flow through a Plate Orifice
• Radial Propagation of Turbulence in Pulsatile Pipe Flow
• Cold Model Experiment on Fluid Flow Phenomena in Hot Dip Plating Bath
• Behavior of Turbulent Slugs in a Transient Pipe Flow
• Mean Flow Characteristics of a Pulsating Round Jet
• A Study on Velocity Profiles of Developing Laminar Oscillatory Flows in a Square Duct
• Flow Pattern and Frictional Losses in Pulsating Pipe Flow : Part 7 Wall Shear Stress in a Turbulent Flow
• Flow Pattern and Frictional Losses in Pulsating Pipe Flow : Part 2, Effect of Pulsating Frequency on the Turbulent Frictional Losses
• Transition to Turbulence in a Pulsatile Pipe Flow : Part 2,Characteristics of Reversing Flow Accompanied by Relaminarization
• Critical Reynolds Number in an Oscillating Pipe Flow
• Free Oscillatory Flow Across a Plate Orifice in U-Shaped Tube and the Resistance Law
• Transition to Turbulence in a Pulsatile Pipe Flow : 3rd Report, Flow Regimes and the Conditions Describing the Generation and Decay of Turbulence
• Flow Pattern and Frictional Losses in Pulsating Pipe Flow : Part 3, General Representation of Turbulent Flow Pattern
• Analysis of Free Oscillating Flow in a U-Shaped Tube
• Turbulence Structure in a Relatively Low Frequency Pulsatile Pipe Flow : Series B : Fluid Engineering, Heat Transfer, Combustion, Power, Thermophysical Properties
• Flow Pattern and Frictional Losses in Pulsating Pipe Flow : Part 6 Frictional Losses In a Laminar Flow
• Loss Coefficients for Flows Through a Sudden Expansion and a Sudden Contraction Closely Placed : Series B : Fluid Engineering, Heat Transfer, Combustion, Power, Thermophysical Properties
• Experimental Study of Turbulence in a Pulsatile Pipe Flow
• Transition to Turbulence and Velocity Distribution in an Oscillating Pipe Flow
• Flow Pattern and Frictional Losses in Pulsating Pipe Flow : Part 4, General Representation of Turbulent Frictional Losses
• Mean Velocity and Turbulence of Water Flow in a Cylindrical Vessel Agitated by Bottom Air Injection
• Dealloying of Cu-Zn Alloy Microchannel Lining Layers for Producing Microporous Catalyst
• Mixing Time in a Cylindrical Bath Agitated by Gas Injection through a Multi-hole Nozzle
• Fabrication of Alumina Coating on Ni-Al Alloy Microchannel Wall for Catalyst Supporting
• Fabrication of Microchannels in Metallic Wire Bundles by a Sacrificial-Core Method
• Anodization of the Inner Wall of the Microchannel Formed in Sintered Aluminum Body
• Alkali Leaching of Ni-Al Alloy Microchannel Lining Layers
• Gas-Liquid Two-Phase Flow through at Orifice in Millimeter-Scale Rectangular Channel
• Fabrication of Ni-Al Alloy Transpiration-Cooling Device by Powder-Metallurgical Microchanneling Process
• Structure Control of Cu-Zn Microchannel Lining Layers with Electrochemical Dissolution
• Characteristics of Poorly-Wetted Two Spheres Penetrating into a Water Bath
• Fabrication of Free-Form Channels by a combined process of Metal Injection Molding and Sacrificial-Core Method
• Anodic Oxidation Behavior of Al-Zn Alloy Lining Layer Produced by a Sacrificial-Core Method
• Composition and Structure Changes in Al_3Ni_2 Microchannel Lining Layers by Alkali Leaching
• Filtration of Ni-Al Alloy Containing By-Product Alumina in Centrifugal Combustion Synthesis
• Cold Model Study of Spout Eye Area in the Presence of the Slag Layer Simulated by Low-Density Particles
• Bubble Behavior in Hg-Air Vertical Bubbling Jets in a Cylindrical Vessel.
• Evaluation of Critical Gas Flow Rate for the Entrapment of Slag Using a Water Model.
• Flow phenomena and heat transfer around a sphere submerged in water jet and bubbling jet.
• The characteristics of water and bubbling jets in a cylindrical vessel with bottom blowing.
• Heat Transfer between Bubbles and Liquid during Cold Gas Injection.
• The Effective Viscosity and Effective Diffusivity of Bubbles in an Air-Water Vertical Bubbling Jet.
• Heat Transfer between Bubbles and Molten Wood's Metal.
• Cold Model Experiments for Developing a New Velocimeter Applicable to Molten Metal.
• The flow field in air-water vertical bubbling jets in a cylindrical vessel.
• Bubble Characteristics in the Buoyancy Region of a Vertical Bubbling Jet.

もっと見る 閉じる

スポンサーリンク